EINHELL TE-SM 36/8 L Li Manual De Instrucciones Original página 23

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 20)
1. Danger! - Read the operating instructions to
reduce the risk of injury
2. Caution! Wear ear-muff s. The impact of noi-
se can cause damage to hearing.
3. Caution! Wear a breathing mask. Dust
which is injurious to health can be generated
when working on wood and other materials.
Never use the device to work on any materi-
als containing asbestos!
4. Caution! Wear safety goggles. Sparks ge-
nerated during working or splinters, chips and
dust emitted by the device can cause loss of
sight.
5. Caution! Risk of injury! Do not reach into
the running saw blade.
6. On/Off switch for laser
7. Warning! To make miter cuts (with the saw
head inclined or the turntable set at an angle),
the adjustable stop rail must be fi xed at an
outer position.
To make 90° crosscuts, the adjustable stop
rail must be fi xed at the inner position.
8. Store the batteries only in dry rooms with an
ambient temperature of +10°C to +40°C.
Place only fully charged batteries in storage
(charged at least 40%). (Not supplied)
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Warning!
Read all the safety information, instructions,
illustrations and technical data provided on
or with this power tool. Failure to adhere to the
following instructions may result in electric shock,
fi re and/or serious injury.
Keep all the safety information and instruc-
tions in a safe place for future use.
Anl_TE-SM_36-8_L_Li_SPK13.indb 23 Anl_TE-SM_36-8_L_Li_SPK13.indb 23
GB
Special information about the laser
Caution! Laser radiation
Do not look into the beam
Laser class 2
VORSICHT ! - LASERSTRAHLUNG !
Nicht in den Strahl blicken!
Laserspezifikation
Laser Klasse 2
: 650 nm; P
•
Never look directly into the laser path.
•
Never direct the laser beam at reflecting sur-
faces or persons or animals. Even a low out-
put laser beam can inflict injury on the eye.
•
Caution: It is vital to follow the work proce-
dures described in these instructions. Using
the equipment in any other way may result in
hazardous exposure to laser radiation.
•
Never open the laser module.
•
It is prohibited to carry out any modifications
to the laser to increase its power.
•
The manufacturer cannot accept any liability
for damage due to non-observance of the
safety information.
2. Layout and items supplied
2.1 Layout (Fig. 1-3)
1. Handle
2. On/Off switch
3. Release button
4. Machine head
5. Saw shaft lock
6. Adjustable blade guard
7. Saw blade
8. Clamping device
9. Guide for workpiece support
10. Workpiece support
11. Locking grip for workpiece support
12. Screw for workpiece support
13. Fixed stop rail
14. Movable stop rail
15. Locking grip for movable stop rail
16. Table insert
17. Adjustable foot
18. Fixed saw table
19. Turntable
20. Locking lever
21. Release button
- 23 -
0
19.10.2023 10:22:25 19.10.2023 10:22:25