ETI Solid State Lighting EM-EL-W-1W Manual De Uso Y Cuidado

NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: Shut off the power at the circuit breaker or fuse panel before removing the old fixture,
ballast, or fluorescent tubes. If you are unfamiliar with electrical installations, we
recommend you contact a qualified electrician to do the installation.
IMPORTANT
Small Battery in this unit may not be fully charged. After electricity is connected
to unit, let battery charge for at least 24 hours. To check, press "TEST" button.
The light will then turn on. The lamps listed herein, when used according to
these instructions with this equipment, are in accordance with the requirements
of csa standard C22.2 NO. 141. Install wiring to remot heads in accordance with
section 46 of the canadian electrical code, part I.
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
• Do not use outdoors.
• Equipment should be mounted in locations at heights where it will not be
subject to tampering by unauthorized personnel.
• Do not mount near gas or electric heaters.
• The use of accessory equipment is not recommended by the manufacturer
may cause an unsafe condition.
• Do not use this equipment for other than its intended use.
• Servicing of this equipment should be performed by qualified personnel.
• Disconnect AC power before servicing.
INSTALLATION (J-BOX MOUNT)
• Feed fixture leads through main case and connect AC power
supply (Fig A).
• Connect wires through J-Box.Main bottom case on J-Box and secure
with screws.
• Connect battery only after continuous AC power can be provided to the
unit (Fig. B).
• Align snaps and push housing directly onto main bottom case (Fig. C).
Apply continuous AC power and press TEST button to check light.
WARNING:
Unused wires must be capped using enclosed wire nuts.
OPERATION：
• During an electrical power failure, the lamps will automatically come on for a
minimum of 90 minutes.
• To test, depress the "TEST" switch. The emergency lamps will illuminate. When
the switch is released, the lamps will go off.
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or
other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV.
•
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
USE AND CARE GUIDE
LED EMERGENCY LIGHTING
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
SAVE THESE INSTRUCTIONS
INSTALLATION (CONDUIT)
1
Secure main bottom case to wall surface. Route wires through hole in conduit flange and make
conduit connection.
2
Connect battery only after continuous AC power can be provided to the unit (Fig. B).
3
Align snaps and push housing directly onto main bottom case (Fig. C). Apply continuous AC
power and press "TEST" button to check light.
(NOTE: To appear outside blue sleeve of terminal before connecting.)
WIRING DIAGRAM
LAMP
LAMP
BATTERY
RED(120V-277)
WHITE(COMM)
Model # 65504102 / 65503102
Part # EM-EL-W-1W / EM-EL-B-1W
Certification # 65504102 / 65503102
FLEXIBLE CONDUIT ONLY
YELLOW(+)
BLUE(-)
YELLOW(+)
BLUE(-)
RED(+)
BLACK(-)
TEST
"READY" LIGHT