Publicidad
The connection is made using a 19 mm inner diameter
hose.
• Provide a minimum dynamic pressure of 1.7 bar.
DANGER
Ö All vented loops (not supplied with the toilet)
must be installed a minimum of 20 inches above
the waterline.
DANGER
Improper installation, defective condition of
the pipes.
Risk of flooding.
Ö Ensure that the pipes are in good condition.
Ö Check that there are no leaks.
Ö The use of a ventilated loop between the pump
and the bowl is required.
NOTICE
Risk of clogging of the solenoid valve.
Ö Install a filter upstream of the pressurized
water circuit.
3.4 ELECTRICAL CONNECTION
NOTICE
Ö It is essential to observe the wiring diagram
in the enclosed instructions.
Advice for wiring up the Sanimarin® Maxlite+S:
Maximum recommended
voltage drop (5%)
Electricity consumption
per second
Current consumption /
Fuses
Electric diameter wire
1.5 mm
2.5 mm
4 mm
6 mm
• Once the connections have been made, finalize the
installation of the rocker switch:
◇ Screw on the supplied bracket.
◇ Recess the switch.
4. COMMISSIONING
When using for the first time, it may be necessary to
prime the pump by pouring a little water into it.
5. USE
Maxlite+S can be used like any normal toilet and will not
require any particular maintenance.
Sequence for the use of the switch keys:
1/ FLUSH: (Add Water) recommended water level:
halfway up the bowl.
2/ DISCHARGE: (Pump out).
3/ FLUSH: (Add Water) to refill the trap in WC pan.
Note : In rough seas, empty the bowl (using the
pump out position) to avoid spillage
IMPORTANT
Only the disposal of toilet paper, fecal matter,
and waste water will be covered under warranty. Any
damage due to foreign bodies such as cotton, condoms,
sanitary towels, wet wipes, food, hair, or liquids such as oils,
solvent products,... will not be covered under our warranty.
12 V
24 V
0.6 V
1.2 V
0.007 Ah
0.004 Ah
300 W / 25 A
360 W / 15 A
= 1 m max
1.5 mm
= 3.5 m max
2
2
= 2 m max
2.5 mm
= 6 m max
2
2
= 3 m max
4 mm
= 9.5 m max
2
2
= 4.3 m max
6 mm
= 14 m max
2
2
6. CLEANING/MAINTENANCE
NOTICE
Ö If away for a long period (holiday,...) or in
the event of a long interruption of electricity,
the water and electricity supplies to the
Sanimarin® Maxlite+S should be switched off (see
procedure in 6.2 Winterizing).
6.1 CLEANING
• For cleaning, use normal sanitary products.
• Do not use aggressive chemicals (such as acetone,
pure bleach, etc.) that could damage the material of
the bowl.
• Use a suitable standard toilet brush; do not use scouring
or abrasive pads.
6.2 CARE
To care for your appliance, apply a polishing paste (such
as car polish) using a polishing cotton pad. Refer to the
instructions for using the polishing paste.
6.3 WINTERIZING
In the event of a long period without use, rinse the bowl
and carry out several flushing cycles with the fresh water
and close through-hull valves.
7. FAULT FINDING
DANGER
Ö Before you begin any work on this
product, make sure that:
- all electrical power to the unit has
been switched off
- and that the through-hull valves are in
the CLOSED or STOP position.
In most cases, any inconsistencies in the operation of the
unit will be minor and easily rectified. Please refer to the
chart below. If the problem cannot be easily remedied
thanks to this chart, please call our Saniflo customer
service phone number.See the table below.
FAULT
PROBABLE
OBSERVED
CAUSES
The motor does
No electricity
not work.
supply.
The motor works
The inlet pipe filter
but there is no
is clogged.
incoming water
The water inlet
for flushing.
pipe is pinched.
The through-hull
valve is closed.
The water injection
nozzle/solenoid
valve is clogged.
The switch is
incorrectly wired
up.
Insufficient water
pressure in the
system
13
EN-US
TROUBLESHOOTING
• Check the control switch.
• Check the electrical
connections.
• Check the power source.
Clean the filter.
Check the pipes.
Check the through-hull
valve.
• Check the water injection
nozzle.
• Check the solenoid valve.
Check the connection of
the cables.
Check the pump/water
unit.
Publicidad
