Publicidad
Idiomas disponibles
Idiomas disponibles
The use of any accessory with this tool not provided or
specified by Snap-on can perform unpredictably.
• Use only accessories provided or specified by
Snap-on.
Tools that perform unpredictably can cause injury.
When disposing of a tool, do it in a way that does not
harm personnel or the environment. Verify that
operators, and maintenance personnel, should be
able to handle the bulk, weight, and power of these
sanders before using or servicing.
SAVE THESE
INSTRUCTIONS
Do not discard the safety
instructions. Give a copy of the
instructions to the operator.
Specifications
Specifications at 90 psig (6.2 bar, 620 kPa)
Free Running Speed ............................. 12,000 opm
Recommended Air Pressure ..... 90 psig (620 kPa)
Air Consumption .................................... 23 SCFM
Air Inlet Thread Size ..........................1/4"-18 NPT
Recommended Hose Size ....3/8" (9.5 mm) ID min
Dimensions:
Length
PSDF4600 .......................................11.3" (285 mm)
Weight
PSDF4600 ......................................2.8 lbs (1.28 kg)
Noise* (Tested in accordance with ISO Standard
15744)
Sound Pressure Level (A)
PSDF4600 ................................................. 78.3 dBA
Sound Power Level (A)
PSDF4600 ................................................. 89.3 dBA
Vibration* (Tested in accordance with ISO
Standard 28927-12)
Vibration Level
PSDF4600 .............................................4.78 m/sec
Uncertainty, K ......................................<1.00 m/sec
*These declared values were obtained by laboratory
type testing with the stated standards and are not
adequate for use in risk assessments. Values
measured in individual work places may be higher.
Values and risk of harm experienced by an individual
user are unique and depend upon the environment
and manner in which the user works, the work piece
and the workstation design, as well as upon the
exposure time and the physical condition of the user.
Snap-on disclaims liability for the consequences of
using the declared values, instead of values reflecting
the actual exposure determined in an individual risk
assessment in a work place situation over which we
have no control.
ZPSDF4600CE Rev B
EN
EN
INTENDED USE
This tool is intended to be used with abrasive sanding
discs for the finish sanding of materials such as wood,
metal, fiberglass and similar materials. If it is used for
anything else, it is considered misuse, creates a hazard
and may void the warranty.
AIR SUPPLY
The efficiency and life of this tool depend on the proper
supply of clean, dry air at a maximum of 90 PSI. The
use of an airline filter, pressure regulator, and lubricator
is recommended. Before connecting to tools, blow out
the airline to remove water and dirt that may have
accumulated.
HOSE AND HOSE CONNECTIONS
The air supply hose recommended is 3/8" (10mm) I.D. If
an extension hose is necessary, use 1/2" (13mm) ID
hose with couplings not less than 3/8" (10mm) I.D. The
tool inlet thread is 1/4" NPT.
LUBRICATION
For maximum performance and tool life, an airline
lubricator, set to deliver 1 drop per minute. Snap-on IM6
Air Motor Oil is recommended. If an airline lubricator is
not used, add 8 to 10 drops of air motor oil to the air
inlet at the start of the day and run the tool for 10-20
seconds. Do not over lubricate because excess oil may
contaminate the surface being sanded.
MAINTENANCE
Water, dust and other airline contaminants can cause
rust and vane sticking. After long idle periods, flush the
tool with a few drops of oil and run for 10 seconds. This
will help remove contaminants and reduce the
formation of rust.
OPERATION
Speed of the tool may be adjusted by turning the
regulator located near the air inlet.
2
Disconnect tool from air supply before installing or
2
removing backing pads or sanding disc.
INSTALLING BACKING PADS
Hold spindle nut with wrench.
Thread pad into spindle and tighten.
INSTALLING SANDING DISC
HOOK and LOOP
Center sanding pad on backing pad and apply firm
pressure.
Be sure the pad is the correct size for the tool.
A mismatch between tool and pad will cause
excessive vibration.
5
(12/20)
Publicidad
