BURG-WACHTER Pure-Safe E FP Instrucciones De Uso página 4

Instruction Manual
Diagram
Keypad CLOSE
To lock the safe
Display
ENTER
Fingerprint sensor
Turn on the electronic lock and
with light ring
confirm the entry of a code
Emergency Lock
Foreword
Dear customer,
Thank you for purchasing this safe from the Pure-Safe series from
BURG-WÄCHTER. This safe is manufactured to a high standard
using the latest in technological advancements.
This Pure-Safe model can be operated with either a code or with
a fingerprint. In addition, all safes have an integrated mechanical
emergency lock.
Important: Please read the entire instructionmanual
before you start programming the safe.
We hope you enjoy using your new Pure-Safe,
Your BURG-WÄCHTER KG
4 I Englsih
Important notes
• Be sure to store your user codes and the emergency key in a secure location
and not inside the safe (the emergency lock is located to the right of the
keypad)
• Don't use simple codes that are easy to guess (e.g. 1-2-3-4-5-6)
• For security reasons we recommend you do not use personal numbers such
as your date of birth or telephone number as a code to operate the safe
• If the safe is not going to be used for a prolonged period of time,
please remove the batteries
• The factory set admin code and default user code must be changed to your
own unique code to ensure the safe is secure
• The safe only achieves its intended protection after it is anchored in place
to a solid part of a building such as a wall or floor. Please use the pre-drilled
anchoring points (in the base and back wall of the safe) fixings to secure the
safe in place
• Please contact your retailer if you have any questions or technical issues
General
An admin code and user code are available to operate the safe, plus the
addition of up to 5 programmable fingerprints.
The admin code must have 8-digits.
The user code can be between 3 to 6-digits.
Admin code: 1-2-3-4-5-6-7-8 (factory set default)
User code: 1-6-8 (factory set default)
Technical specification
Blocking Times: After 3x wrong code entries: 5 minutes
Battery Specification: 4x AA MIGNON LR6 ALKALINE
Specified operating -15 °C to + 50 °C
conditions up to 95% rel. humidity
(non-condensing)
Signal tones
1 x beep Key entry registered
2x beeps Input correct / accepted
3x beeps Input wrong / denied
1x long beep Fingerprints deleted successfully
Light ring
The light ring is used to indicate the current state of the fingerprint
sensor and is located around the sensor:
Blue light The fingerprint sensor is ready for use
Green light The fingerprint has been set up successfully
Installation
• Remove the enclosed emergency keys from the packaging.
• Use the emergency key to open the safe door (see diagram for location).
• Remove the plastic strip located by the battery compartment on the
inside of the door to activate the batteries.
• With the door still open, turn the emergency key and remove it from
the emergency lock hole.
• Press the ENTER button.
• Enter the user code (factory default code: 1-6-8) and confirm by
pressing the ENTER button.
• The safe can now be programmed to your own admin and user code.
Chapter 1: Operation with a code
Opening the safe with the user code
• Press the ENTER button
• Enter the 3 to 6-digit user code (factory default code: 1-6-8) and confirm
with ENTER button. You will hear 2 short beeps.
The door will open automatically.
If you hear 3 short beeps, an incorrect code has been entered. Please try again.
Closing & locking the safe
Push and hold the door of the safe in the closed position. Press the CLOSE
button to automatically extend the bolts and lock the safe.
Note: If something is blocking the door during the locking procedure, the
display will show"BLOCK" to indicate the safe cannot be locked. Please remove
the obstruction and try again.
Programming the user code
The door must be open and the bolts must be retracted inside the door.
• Press the ENTER button.
• Enter a new user code (it must be between 3 to 6 digits max.) and
confirm with the ENTER button. You will hear 2 short beeps to confirm.
• Press the CLOSE button.
The locking bolts will extend out. A new user code has been successfully
programmed.
Incorrect entries
If an incorrect code or fingerprint entry is made when the safe is locked/closed
the display will show "CODE-ERROR" or „FP-ERROR" and you will hear 3 short
beeps. A third successive incorrect code or fingerprint entry will result in the
electronic lock blocking any further entries for 5 minutes. After this blocking
time, the safe can be opened with the admin code, the correct user code or a
valid fingerprint. If a wrong digit is entered during code entry, it can be cleared
by pressing the CLOSE button.
Pure-Safe Electronic E FP