Descargar Imprimir esta página

LiftMaster EL1SS-P Manual De Instalación Y Configuración página 14

Publicidad

Idiomas disponibles

Idiomas disponibles

INTRODUCTION
TEST GATE/DOOR RELAYS
TEST RELAY 1
Enter a 4 digit Master Code + 1
The 1 Key indicates the Relay to be triggered.
NOTE: Relay 1 status indicator LED will illuminate (Blue) to
show activity when triggered.
TEST THE TELEPHONE CONNECTIONS
1. Place a telephone call from the resident's telephone to verify it is
operating properly, then hang up the phone.
NOTE: To ensure proper function of the audio and authorization
tones, keep the telephone handset at least 10 feet (3 m) from the
EL1SS during testing.
2. Ensure EL1SS is programmed for Telco or Intercom mode based
on application.
3. Press the "Call" key on the unit's keypad. The telephone in the
residence should ring.
NOTE: After the "Call" Button is pressed, the "Status" LED on the
processor board will blink during transmission.
4. To test Relay 1 press the "Call" button and have someone answer
the telephone and enter "*9" (Star + 9). The EL1SS will disconnect
the call as soon as the relay is activated. To test Relay 2 have
someone answer the telephone and enter "*5" (Star + 5). The
EL1SS will disconnect the call as soon as the relay is activated.
OPERATION
The EL1SS requires a Master Code (see page 12) to set up basic functions and settings. Use the STAR Key "
When the unit is being set up, certain tones will be heard (see chart below). Keypad commands should be entered in a single string to be
successful (indicated by a dual tone beep). Stop and go keystrokes will result in a negative tone (three short low tone beeps).
Three Short Low Tone Beeps
Dual Tone Beep
Three Short Low Tone Beeps
USING ENTRY CODES
The Entry Codes allow residents to activate an entry device connected to a relay (Relay 1 or Relay 2). There are two types of entry
codes available in this system. A Standard 4-Digit Code ONLY triggers the relay (1 or 2) the code has been assign to. A Special
Use 5-Digit Code (4-Digit Code + 1 or 2) triggers the corresponding relay that matches the last entered digit. Choosing between the
Standard 4-Digit Code or the Special Use 5-Digit Code entry codes depends on the application, standard 4-digit codes maximize
memory capacity for systems controlling two access points for a large number of users. Special use 5-digit codes provide custom
secured access for two independent access points (see chart below).
Standard 4-Digit Code
Special Use 5-Digit Code (Relay 1)
Special Use 5-Digit Code (Relay 2)
ANSWERING CALLS FROM EL1SS
When the home phone receives a call from the EL1SS, answer the call to initiate the audio and to speak to visitor.
To deny the caller access to the property, hang up. To extend the talk time press 0 or continue talking.
GRANTING ACCESS
Press
*
9 to grant access through the door or gate connected to Relay 1. The call will end.
OR Press
*
5 to grant access through the door or gate connected to Relay 2. The call will end.
INSTALLATION
Failure
Valid code is entered
Error or invalid code is entered
Entry Code (4 digits)
Entry Code (4 digits) + 1
Entry Code (4 digits) + 2
TEST
TEST RELAY 2
Enter a 4 digit Master Code + 2
The 2 Key indicates the Relay to be triggered.
NOTE: Relay 2 status indicator LED will illuminate (Blue) to
show activity when triggered.
Activates the pre-assigned relay when the code was created
Activates relay 1
Activates relay 2
13
SET UP
Call Button
" to cancel any input.
*

Publicidad

loading

Este manual también es adecuado para:

El1ss