Dual CR 900 RC Instrucciones De Manejo página 10

Automatic Station Search Run (AUTO SCAN)
Your tuner is designed to automatically select a station transmitting
with an adequate antenna voltage when the station search key
— Press key PRESET SCAN 23 again. The last station played
remains tuned.
— All the station memory locations can be selected in tum by
AUTO 24 is pressed. repeatedly pressing the PRESET SCAN 23 key
— Select wave band with key FM 11 or AM 12,
— Press key AUTO 24, FM Stereo Reception, Mono
— Start station search in the desired direction by pressing key
TUNING b» 26 or 4 27,
— lf necessary, press the key again to start the search for the next
station.
The appliance is designed for the reception of stereo radio broad-
casts.
— If a stereo broadcast is received whilst the mono key 25 is not
depressed, the appliance automatically switches to Stereo mode
(Display FM STEREO).
— If the key MONO 25 is pressed, the appliance operates in mono.
This mode is also recommended for stereo broadcasts with
Storing Preset Stations at Desired Memory Location
40 different FM or medium wave stations can be stored using the
station keys 5. severe noise.
— Tune in to the desired station manually or using the automatic
station search run. Tape recordings
* Station memory locations 10 to 19, 20 to 29, 30 to 39:
By pressing one of the buttons 1, 2 or 3 (5), followed by one of the
buttons 1 to O within 1.5 seconds.
— All other stations are stored in the same way.
Automatic Programming of the Station Keys
Station memory locations 1—40 which are not already assigned can
be automatically programmed in sequence.
In addition, the existing assignment of a station memory location can
be cancelled (see "Cancelling Station Memory Locations").
— Tune to the desired station (see "Selecting Stations and Wave
— The recording levels must be selected in accordance with the
instructions for the recording equipment.
Checking the recording standard
You can check the standard of the recording being made if your
recorder has a supplementary magnetic head allowing the recording
to be monitored simultaneously.
This is only possible with a recording made by recorder 1. To do this
connect the recorder to the jacks 37 and 38.
— Press one of the buttons 10, 11, 12, 13, 14 or 16, depending on
the source to be recorded.
Bands"). = 4 É
s key MEMORY 22; the "PRESET" di " : Press button 15: the TAPE 1/MONITOR lamp lights up.
— Press key MEMORY 22 again. Tape copy
— The selected station is stored at the lowest vacant memory KEF
location.
You can copy recordings if you have another tape recorder at pour
— When all the memory locations have been assigned, FULL disposal (recorder 2) connected to sockets 37 and 38:
appears on the display. € Copy from recorder 1 (playback) onto recorder 2 (recording).
— Press button 15: The TAPE 1/Monitor lamp lights up.
@ Copy from recorder 2 (playback) onto recorder 1 (recording).
— Press button 16: the TAPE 2 lamp lights up.
Note: Tape recorder 2 can be replaced by a hifi video cassette
recorder.
Disconnecting preamplifier output
and main amplifier input
The preamplifier outputs EXT PROC OUT 46 and the main amplifier
inputs EXT PROC IN 47 are connected by contact.
Preamplifier and main amplifier can be disconnected from each
Erasing Station Memory Locations
Before the station keys can be automatically programmed, the
previous assignment must be erased.
— Hold key MEMORY 22 depressed for five seconds until the
station memory location display goes blank.
— All station memory locations are now vacant.
Calling Up Preset Stations
The 40 preset stations already programmed by you can be called up
by pressing keys 1 to 0 (5).
— Call up station memory locations 1 to 9 by pressing the corre- other by removing these bridges. »
зропдпа кеу 1-9. This permits the interconnection, for example, of a graphic equalizer.
— Forstation presets 10 to 19, 20 to 29 or 30 to 39, press button 1,
2 or 3, followed by one of the 10 buttons within 1.5 seconds. Changing the batteries
— Station preset 40 by pressing button 0-40.
PRESET SCAN - PRESET Station Search Run
— Press key PRESET SCAN 23.
— The remote control unit is powered by two 1.5 volt mignon cells
IEC R 6.
— The batteries must be changed once you notice any reduction in
Each of the stations programmed using the station keys 5 are
played in tum for 5 seconds.
range.
— The battery compartment is located on the rear of the remote
control unit.
FRANGAIS
POWER Interrupteur principal.
PHONES Prise pour casque stéréo à valeur ohmique
moyenne et haute, avec fiche à jack 6,35 mm (recomman-
dation: 8 — 600 Ohms).
SPEAKERS A Sélecteur pour la paire 1 de haut-parleurs.
SPEAKERS B Sélecteur pour la paire 2 de haut-parleurs.
Touches de stations pour mémoires émetteurs.
BASS Réglage des graves.
Na
naw
10
7 TREBLE Réglage des aigües.
Réglage des graves et des aigües possible simultanément pour
les deux canaux. En position du milieu, la courbe de réponse
est lineaire. Attention: Lorsque le bouton est réglé au maximum
et si le volume est trop fort, les haut-parleurs risquent d'être
surchargés.
8 BALANCE Pour adapter le volume des deux canaux à l'es-
pace environnant, en cas p.e. d'installation asymétrique des
enceintes.