Publicidad
Idiomas disponibles
Idiomas disponibles
Fig.0:
(81) Main body; (31) Saddle post; (79)
Rear
stabiliser
stabiliser bar; (24) Saddle; (102)
Handlebar post; (1) Monitor; (21)
Handlebar; (5) iPad support tube; (2)
iPad support; (97) Front stabiliser
cover; (92) Tapa caballete trasero;
(48) Pedals; Mains transformer.
Bag of screws containing: (6) Flat
washer
D19xD8,5x1,5;
washer
D12,7xD8,3x2,2;
M8x20; (90) Screw M8x25; (50-4)
Washer
170/175; (50R-3) Nut
170/175; (50L-3) Nut L 170/175; (50-
1) Washer 172,5; (50L-2) Nut L 172,5;
(50R-2) Nut R 172,5; Wrenches.
2. Position the machine's front stand
on the front stabiliser bar (60), as
shown in Fig.1, insert the bolts (90), fit
the washers (7), (6) and then tighten
securely. Remove the screws (38),
place the front cover (97), and refit the
screws (38).
3. Position the rear stabiliser bar with
wheels (79) as shown in Fig.1, insert
the bolts (90), fit the flat washers (7),
(6) and tighten securely. Remove the
screws (38), place the rear cover (92),
and refit the screws (38).
4.- ATTACHING THE SADDLE.-
Attach the saddle (24) to the upper
(25) and lower (26) fix sheet and
secure it using the screws (29), (30),
the nuts (28) and the bushings (27),
Fig.2A. The shorter screw (29) should
be placed in the front.
Insert the saddle post (31) into the
hole on the main body (81) and tighten
the clamp (40), Fig.2.
bar;
(60)
Front
(7)
Spring
(8)
Bolt
ADJUSTING THE SADDLE HEIGHT.-
Loosen the clamp (40) slightly, Fig.2,
move
the
comfortable for doing exercise and
then tighten the clamp (40) securely.
5.- FITTING THE PEDALS.-
The assembly instructions for the pedals
must be followed to the letter, fitting
these incorrectly could damage the
screw thread on either the pedal or the
crank. Right and left refer to the position
that the user adopts when sitting on the
saddle to do the exercises.
R
Two types of nuts are included to adjust
the length of the pedal cranks (one of
172.5 and the other of 170/175), Fig.3A.
The side (L for the left pedal and R for
the right pedal) and the size are marked
on the nuts.
Choose the nut (for example (50R-3) for
the 175 right nut) and install it on the
corresponding crank in such a way that
the measurement is on the inside of the
connecting rod, Fig.3B. Place the
corresponding washer ((50-4) for the
175) nut) on the other side of the crank,
matching the holes.
Then fit the pedals.
The right-hand pedal (48R) marked with
the letter (R), screws onto the right-hand
crank (50R), also marked with an (R), in
a clockwise direction. Tighten securely,
Fig.3.
The left-hand pedal (48L) marked with
the letter (L), screws onto the left-hand
crank (50L), also marked with an (L), in
an anti-clockwise direction. Tighten
securely, Fig.3.
6.- FITTING THE HANDLEBAR.-
Bring the handlebar post (102) close
to the main body (81) and connect the
upper computer cable (15) with the
lower computer cable (84), Fig.4.
14
saddle
to
a
position
Publicidad
