Publicidad
Idiomas disponibles
Idiomas disponibles
o Watch out for foreign objectsin the
grass
SHRUB
CLIPPER
,, The clipper
works
best with dry
shrubbery
and bushes,
but it could
be
used safely
with wet growth
due to
the low voltage
design
o A wide
sweeping
cutting
motion
away
from the body is recommended,
and
will get the greatest
amount
of clip-
ping per charge,,
o A slight downward
tilt of the blade,
in
the direction
of motion
gets the best
result,
o To cut thicker
twigs,
use a little extra
pressure
as you feed the blade
through
the growth,
o This unit should
NOT be used for
large trees
and hedges
with limbs in
excess
of 5/16th
of an inch
o Watch
out for foreign
objects
CAUTION:
lfthe
blades
become
JAM_
MED
or stalled
on a branch,
stick,
or
foreign
object,
release
the trigger
im-
mediately
Failure
to stop the unit when
the blades
are jammed
will cause
ex-
cessive
battery
drainage
and shorten
motor
life (overheating).
After the
blades
have completely
stopped
moving,
carefully
remove
the obstruction.
BLADE CLEANING
- After you have
OTHER
LUBRICATION
- No periodic
re-lubrication
of the clipper's
bearings
or other moving
parts are required
CLEANING
PLASTIC
PARTS
- Use
only warm
water
and mild soap to
clean
plastic
parts
Many
household
cleaners
contain
chemicals,
which
could
damage
the plastic,
Never
use
gasoline,
turpentine,
paint thinner
or
similar
fluids,
BLADE
NICKS
AND
BURRS
-If
you
accidentally
hit a wire,
fence,
stone,
or
other
hard object,
you may put a nick
on the blade.. There
is no need to re-
move this nick or burr as long as it
does not interfere
with the movement
of the blades
If it does interfere,
use
ONLY
an oilstone
to remove
it. DO
NOT file or grind the blade as it will
alter the steel temper
and reduce
useful
life.
DROPPING
THE COMBO
CLIPPER
-
If you drop the unit, carefully
inspect
it
for damage,
if the blade
is bent,
hous-
ing cracked,
or if you see any other
condition
that may affect the safe op-
eration,
contact
your local Sears
store
for repairs,
finished trimming,
you may find that dirt
and vegetation
have accumulated
on
the blades, Wash the blades in water
after each use to prevent build-up, Hold
the unit, tilting it forward, to ensure that
NO water gets into the unit or the blade
gearbox, Only the blade tips should be
held under running water or in a pan of
water, Turn tool "ON" to help dislodge
any deposits,
BLADE
LUBRICATION
- After clean-
ing the blades,
wipe them with a cloth
and allow to them dry
Then,
with a rag,
apply
a thin film of engine
oil to the top
and bottom
of blades
DO NOT overly
oil Turn the unit ON for a few seconds
to work lubricant
between
the blades
IMPORTANT:
To assure
product
SAFETY
and RELIABILITY,
repairs
and adjustments
should
be performed
by Sears
service
or other
qualified
service
organizations,
always
using
identical
replacement
parts.
TEMPERATURE
- Temperature
ex-
tremes
limit the useful
life of the bat-
tery. The best storage
place
is one that
is cool and dry
Store
the tool away
from direct sunlight,
heating
pipes,
furnaces,
etc
Do not store where
tem-
peratures
go below
+40 F or above
+120
F
5
Publicidad
