Operating Elements - Martin Yale Industries Intimus POWER 16.87 Instrucciones De Uso

SCHALTBILD / WIRING DIAGRAM / PLAN DE MONTAGE / DIAGRAMA ELÉCTRICO
ESQUEMA ELECTRICO / SCHEMA ELETTRICO / SCHÉMA ZAPOJENÍ
60
16.87
GB
OPERATING ELEMENTS (Fig. 6, 7 und 8):
1 = Mains switch (emergency stop) (fig. 6)
This switch is used to switch the complete
unit on and off (position „1" or „0").
The „ready" (7), and „ram at rear" (11)
indicator lights come on to indicate cor -
rect function, or flash to indicate incorrect
function.
Note: The lights come on after a delay of
approx. 2 seconds (initializing routine for
the microprocessor).
2 = Key switch (fig. 6)
This switch can be used to lock the unit (turn
key to left) and so prevent unauthorized
use.
Note: If the unit is locked when the mains
switch (1) is switched on, the „ready" indi
cator light (7) flashes to indicate that the
unit is not ready for operation"
3 = „Cutter forwards" pushbutton (fig. 6)
When this button is operated, the cutter and
conveyor belt start and the machine can be
fed.
Note : If, when the shredder is started, the
baling ram (32) of the baler is not in its basic
position (rearmost position), a compression
stroke with following return stroke is carried
out automatically before the cutter and
conveyor belt start.
4 = „Stop cutter" pushbutton (fig. 6)
When this button is operated, the shredder
is switched off and the cutter and conveyor
belt stop.
5 = „Cutter reverse" pushbutton (fig. 6)
When this button is operated, the cutter and
conveyor belt operate in reverse.
Note : If the button is operated during forward
operation, reverse operation will occur for at
least 3 seconds, before forward operation
resumes automatically.
6 = „Cutter forwards" indicator light (fig. 6)
a) Comes on
belt operate forwards.
b) Flashes
are switched from forwards operation to
reverse operation, or if the baling ram
was not in the basic position (rearmost
position) when the „cutter forwards"
pushbutton was operated.

OPERATING ELEMENTS

7 = „Ready" indicator light (fig. 6)
Comes on (ready for operation) when
a) the mains switch (1) is switched on,
b) the key switch (2) is released,
c) the emergency stop bar (14) is pulled out,
and
d) the actuator of the safety switch activator
(19) is inserted in the limit switch at the
baler (fig. 3).
Flashes (not ready for operation) when the
mains switch is switched on if
a) the key switch (2) is locked, or
b) the emergency stop bar (14) is pressed,
or
c) the actuator of the safety switch activator
(19) is not inserted in the limit switch at
- the baler
8 = „Malfunction - motor
. " indicator light (fig. 6)
Flashes if the motor of the shredder or baler
is overloaded and the installed thermostat
has broken the circuit for full operation.
For further details see the „motor defect"
section.
9 = „Outlet jam" indicator light (fig. 6)
Flashes if the space above the rear conveyor
belt is completely filled with paper due to a
jam of the inlet opening, and the unit has
been switched off due to the raised cover
flap (27).
For further details see the „outlet jam" sec
tion.
10 = „Cutter reverse" indicator light (fig. 6)
Comes on when the cutter and conveyor
belt operate in reverse.
11 = „Ram at rear" indicator light (fig. 6)
a) Comes on if the baling ram (32) is in its
basic position (rearmost position).
b) Flashes if the baling ram (32) is not in its
basic position. In this case, operate the
„cutter forwards" pushbutton (3) at the
when cutter and conveyor shredder, or the „ram reverse" pushbutton
(17) at the baler.
when cutter and conveyor belt 12 = „Bale ready" indicator light (fig. 5)
Flashes when the bale volume has been
achieved, and the bale must be bound and
ejected. For further details see the „binding
and ejecting the bale" section.
14
fig. 7
13
16.87
13 = „Baler open" indicator lamp (fig. 6)
Flashes if the inlet flap (30) or discharge
flap (31) is open.
Note : If a door or flap is open the shredder
cannot be started. The baling ram in the
baler can, if the inlet flap is closed, still be
operated by inching , forwards (to eject a
bale), or in reverse (return stroke).
14 = Emergency stop bar (fig. 7)
Should it be necessary, for any reason, to
switch off or stop the machine as quickly as
possible, this can be achieved by pressing
the emergency stop bar. To switch on again,
release the bar (pull it out) and operate the
„cutter forwards" pushbutton (3).
15 = „Advance Ram" Key
(compacting cycle) (fig. 8)
If this key is pressed, the baling ram (32)
is advanced (compacting cycle) and is then
automatically retuned to its rear, home
position.
Note: If the ram does not return to its home
position, but rather continues to press
against the bale, the bale must be tied off
and then ejected (see "Tying Off and Eject -
ing the Bale").
16 = „Stop Ram"or
"Open Discharge Flap" Key (fig. 8)
a) Stop Ram
If this key is activated briefly (less than
- 2 seconds), the baling ram (32) is stop -
ped.
b) Open Discharge Flap
If the key is pressed and held (for at least
2 seconds), the baling ram travels a short
distance in reverse and the locking lever
(35) (fig. 2) is advanced a short distance
(pressure relief at the discharge flap).
The discharge flap (31) can now be
opened. This is necessary when the
baler is holding the bale in the com -
pacted condition.
Note: The discharge flap can only be
opened after this key has been acti -
vated.
17 = „Return Ram" Key
(return stroke) (fig. 8)
When this key is activated in the automatic
operating mode, the baling ram (32) is
returned to its rear, home position.
15 16
17
fig. 8