Makita PF400MP Manual De Instrucciones Original página 10

4. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
Do not use a battery pack or tool that is dam-
5.
aged or modified. Damaged or modified batteries
may exhibit unpredictable behaviour resulting in
fire, explosion or risk of injury.
6. Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or tem-
perature above 130 °C may cause explosion.
Follow all charging instructions and do not
7.
charge the battery pack or tool outside the
temperature range specified in the instruc-
tions. Charging improperly or at temperatures
outside the specified range may damage the
battery and increase the risk of fire.
Electrical and battery safety
1. Do not dispose of the battery(ies) in a fire.
The cell may explode. Check with local codes for
possible special disposal instructions.
2. Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if
swallowed.
3. Do not charge battery in rain, or in wet
locations.
4. Do not charge the battery outdoors.
5. Do not handle charger, including charger plug,
and charger terminals with wet hands.
Do not replace the battery in the rain.
6.
7. Do not replace the battery with wet hands.
8. Do not replace battery in the puddle or on a
wet surface.
Service
1. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
2. Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
PARTS DESCRIPTION
► Fig.3: 1. Cap 2. Pipe 3. Water inlet 4. Water outlet
5. Hose clamp
ASSEMBLY
WARNING:
the equipment, switch off the motor and remove
the battery cartridge. Otherwise, the machine may
start unintentionally and result in an injury.
WARNING:
the equipment, always put it down. Assembling or
adjusting the equipment in an upright position may
result in serious injury.
WARNING:
tions in the chapter "SAFETY WARNINGS" and
the instruction manual of the power unit.
Assembling the pump attachment
1. Remove 2 bolts.
► Fig.4: 1. Bolt
2. Insert the pipe into the pump head so that the hole
on the pipe is aligned with the hole on the pump head.
Tighten 2 bolts securely to fix the pipe.
► Fig.5: 1. Hole 2. Pipe 3. Bolt
NOTE: When tightening the bolts, apply 2.5 - 4.5 N•m
as tightening torque.
Mounting the attachment pipe
CAUTION:
Always check that the attachment
pipe is secured after installation. Improper instal-
lation may cause the attachment falling off from the
power unit and cause personal injury.
Mount the attachment pipe to the power unit.
1.
Remove the cap from the end of the pipe.
► Fig.6: 1. Pipe 2. Cap
NOTICE:
Do not dispose of the cap since the cap
is necessary for storing the attachment.
2.
Turn the lever toward the attachment.
► Fig.7: 1. Lever
3. Align the pin with the arrow mark on the power
unit. Insert the pipe until the release button pops up.
Make sure that the position line is on the tip of the arrow
mark on the power unit, and the arrow mark on the power
unit and the arrow mark on the pipe are facing each other.
► Fig.8: 1. Release button 2. Arrow mark on the power unit
3. Pin 4. Position line 5. Arrow mark on the pipe
4. Turn the lever toward the power unit.
► Fig.9: 1. Lever
Make sure that the surface of the lever is parallel to the pipe.
NOTICE:
Do not tighten the lever without the
attachment pipe inserted. Otherwise the lever may
tighten the entrance of the drive shaft too much and
damage it.
To remove the pipe, turn the lever toward the attachment and
pull the pipe out while pressing down the release button.
► Fig.10: 1. Release button 2. Lever 3. Pipe
10 ENGLISH
Before assembling or adjusting
When assembling or adjusting
Follow the warnings and precau-