Publicidad
Idiomas disponibles
Idiomas disponibles
GETTING STARTED
• Use the glass stage: press the glass stage on the sunken place then the other side of
the glass stage will be lifted.
• Set the specimen slide: set the specimen in the center of stage plate. If necessary,
clamp the slide with the clips. Turn on the light.
• Diopter and focus adjustment: the focusing knob and observe the specimen through
the right eyepiece till the image of the specimen is clear. Observe the specimen through
the left eyepiece and adjust the diopter adjustment ring till the image is clear.
• Adjust the interpupillary distance: adjust the prism housing along the direction of
arrow till the observation is comfortable.
• Use eyepiece shields: for user who does not wear glasses, hold the diopter-adjusting
ring to prevent them from rotating and turn the eyepiece till the eyepiece shield fit the
observer well. For user who wears glasses, take the eyepiece shields off
before observation.
• Installing and removing the optional eyepiece micrometer: turn and remove the
mounting ring from the eyepiece. Clean the eyepiece micrometer and mount it to the
mounting ring with the inscription side downward. Gently twist the mounting ring with the
eyepiece micrometer into the eyepiece till tightening securely. To remove the eyepiece
micrometer, take down the mounting ring by twisting and take out of the micrometer and
the wrap it in clean soft paper for storage.
• Install the illumination device: insert the illumination device in the bracket with the
protrudent side toward the lock-screw and tighten the lock-screw. Put the plug into the
socket of the pillar stand.
• Choose the optical system: you can alternate the binocular and video capture by
pushing or pulling "the pole". You can attain binocular observation by pushing "the pole"
inside, or attain video capture by pulling it outside.
• Adjust the brightness of the bottom light: turn knob clockwise to increase,
counterclockwise to decrease, following base markings.
• Mount the photo eyepiece and the PK-mount adapter: put the photo eyepiece into
the eyepiece socket of the tri-ocular. Connect the PK-mount adapter with the photo
eyepiece and then tighten the lock-screw.
• Replace the lamps: press the stage on the sunken place then the other side will be
lifted. Take the lamp out of the jack. Put a new lamp into the jack thoroughly. Recover
the stage plate. Note: before replacing the lamps, turn off the power first. Avoid violence
while the lamp is plugged into the jack.
• Replace the fuse: screw the fuse tube out with a screwdriver and pull the fuse out of
the tube. Remove the fuse and mount it in an adverse way.
POWER OPTIONS
Main power cable (100~230V/50Hz), available for EU (item no. 76995), UK (item no.
76999), CH (item no. 76998) and USA (item no. 76996).
DOUBLE SAFETY IS GUARANTEED
• Full separation from the main power through DPDT* switch.
• Indicator LED to show if main power is switched on and if optional battery is charged
• Potentiometer for regulation of the High Power LED
• High Power LED for bright image
*DPDT (double pole, double throw) when switched off, the power is completely shut off.
The BMS EduLed microscope has a LED illumination light source. This light source is
characterized by low maintenance and low power consumption. This LED source has an
average life span of 50,000 hours. Besides that, this LED illumination system lacks heat
development and is therefore safe to use by children. It is recommended though that an
adult is supervising at all time
SAFETY INFORMATION
• Always disconnect mains plug from power point before maintenance
• Work in a clean and proper environment
• Think of the safety of yourself and those working around you
• Clean all parts coming in contact with the observed specimen to prevent infection
• Place the microscope on a sturdy, level table or working surface
• Always use original accessories
CAUTION
The delicate components may get damaged if the microscope is not handled with care.
Use the microscope in a clean environment. Do not use it when it is subject to direct
sunlight, high temperatures, humidity or dust. Carry the microscope with care, do not
hold it by the stage. Remove specimen before transport.
CARE & MAINTENANCE
• Please use our special microscope maintenance kit (item no. 76026).
• Always keep the optical parts clean. Please use the dust cover to protect it.
• Avoid contamination of the objectives.
• In case there is dirt on the lens surface, use distilled water to moist and soft cloth to
clean the lens surface. Be very careful and make sure to avoid scratches on a lens
surface. Cleaning can also be done by using an alcohol solution or an optical cleaning
solution. Ventilate the room. Do not soak the lens in (cleaning) liquid.
• To clean the eyepiece- and objective-lens surface, move the cloth in a spiral motion
from the center to the rim.
• Never make a zig-zag movement since this will only spread the dirt.
• To clean painted parts, use also a slightly moistened soft cloth.
• Never use an organic solvent. Use a mild detergent, like soft hand soap.
• Do not remove the objectives from the nosepiece. The objectives were placed in a
particular sequence and are adjusted in order to have a parcentered optical system.
• Never dismantle the microscope. This can only be done by factory and/or dealer
authorized staff.
SPECIFICATIONS
For more specifications, please view the product page on the website:
www.bmsmicroscopes.com
It is within our company policy to develop continuously. BMS Microscopes b.v. reserves
the right to change design and specifications without further notice.
BMS Microscopes b.v.
Essebaan 50
2908 LK Capelle aan den IJssel
The Netherlands
Tel.: +31(0)10 458 42 22
E-mail: sales@bmsmicroscopes.com
Environment protection first!
Your appliance contains valuable materials which can be recovered
or recycled. Leave it at a local civic waste collection point.
Publicidad
