Bosch 0.601.64L.901 Manual Original página 14

OBJ_BUCH-1272-007.book Page 14 Wednesday, October 12, 2016 12:19 PM
14 | English
13 Saw blade holder
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Sabre saw
Article number
Rated voltage
Stroke rate at no load n
0
Tool holder
Stroke
Cutting depth, max.
– in wood
– in non-alloy steel
– Pipe diameter
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
– during operation* and during
storage
Recommended batteries
Recommended chargers
* Limited performance at temperatures <0 °C
Technical data deter
ed with battery from delivery scope.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-11.
Typically the A-weighted sound pressure level of the product
is 70 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-11:
2
Cutting board: a =8.0 m/s , K=1.5 m/s
h
2
Cutting wooden beam: a =12.0 m/s , K=1.5 m/s
h
The values given for sawing particle board apply for a workpiece thick-
ness of 20 mm.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
1 609 92A 2PA | (12.10.16)
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
GSA 10,8 V-LI
We declare under our sole responsibility that the product de-
3 601 F4L 9..
scribed under "Technical Data" is in conformity with all rele-
V= 10.8
vant provisions of the directives 2009/125/EC (Regulation
-1
min 0 – 3000
1194/2012), 2011/65/EU, until 19 April 2016:
2004/108/EC, from 20 April 2016 on: 2014/30/EU,
SDS
2006/42/EC including their amendments and complies with
mm 14.5
the following standards: EN 60745-1, EN 60745-2-11,
EN 50581.
mm 65
Technical file (2006/42/EC) at:
mm 8
Robert Bosch Power Tools GmbH, PT/ECS,
mm 50
70538 Stuttgart, GERMANY
Henk Becker
kg 1.2 – 1.4
Executive Vice President
Engineering
°C 0...+45
°C –20...+50
GBA 10,8V ...
Robert Bosch Power Tools GmbH
AL 11..
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
Battery Charging
 Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
2
,
2 The lithium-ion battery is protected against deep discharging
.
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
Observe the notes for disposal.
Removing the battery (see figure A)
To remove the battery 12 press the unlocking buttons 5 and
pull out the battery downwards. Do not exert any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
9 indicate the charge condition of the battery 12.
Press the On/Off switch 7 halfway or completely through to
indicate the charge condition.
Helmut Heinzelmann
Head of Product Certification
PT/ECS
Bosch Power Tools