Publicidad
At the end of work:
►
release the brush lever (fig. D, ref. 1);
►
turn the machine off by pressing the button (fig. C, ref. 3) for at least 4 seconds.
►
use the lever provided (Fig. D, ref. 2) to raise the squeegee off the floor and prevent continuous pres-
sure from deforming the drying blades, standard version with brushes and drive disks;
►
remove the brush (or drive disk) to prevent it from warping permanently;
►
use the handle to raise the front of the machine and fit the transport wheel, thus preventing continuous
pressure from deforming the drying blades and the brush roller, roller version.
►
depending on the model, unplug from the mains socket or disconnect the batteries,
►
empty and clean the dirty water tank.
Some useful tips to get the most from your scrubber drier
In the event of particularly stubborn dirt on the floor, washing and drying can be performed in two separate ope-
rations.
Prewashing with brushes or pads
►
press the main switch (fig. C, ref. 3) (LED on);
►
press the brush button (fig. C, ref. 4) (LED on);
►
press the suction button (fig. C, ref. 5) (LED off) to turn suction off;
►
operate the brush lever (fig. D, ref. 1) to enable brush rotation;
►
make sure the suction motor is off and the squeegee is raised;
►
begin washing.
►
adjust the flow of detergent to the brush by means of the detergent tap (fig. G, ref. 2). Flow speed
must be regulated according to the operator's chosen advance speed. The slower the machine moves
forwards, the less water is needed.Persist when washing particularly dirty points to give the detergent
time to perform its chemical action detaching and suspending the dirt and the brushes time to exert an
effective mechanical action.
Drying
Lower the squeegee and with the suction motor on, pass over the same area washed previously. The result is
equivalent to in-depth washing and subsequent ordinary maintenance will take less time.
To wash and dry at the same time, operate the brush, detergent flow, squeegee and suction motor simultaneously.
Carpet cleaner accessory
This accessory comprises a slider that can wash and dry any type of carpet.
Assembly instructions:
►
switch the machine off.
►
empty the dirty water tank and the clean water tank.
►
tilt the machine by lifting the front, until it is almost vertical.
►
remove the two squeegees (Fig. P, ref. 2-3) by unscrewing the screws.
►
place the slider in position (Fig. P, ref. 2) and fasten it using the screws.
►
lift the cover (Fig. R, ref. 2) and insert the cap supplied together with the accessory, with the holes facing
upwards.
►
close the cover to lock it in position.
Operation:
Turn the function selector to CARPET (Fig. R, ref. 1).
Start working, the machine must only be used moving backwards.
Combi accessory
The Combi accessory is used for washing in positions that the floor scrubber cannot reach, such as corners, stairs
or around obstacles.
To use the accessory, proceed as follows:
►
switch the machine off.
►
lift the cover (Fig. R, ref. 2) and fit the Combi attachment in position (Fig. S, ref. 1) with the hole facing
upwards.
►
close the cover (Fig. R, ref. 2) on the Combi attachment to lock it in position.
►
if installed, turn the function selector to STANDARD (Fig. R, ref. 1).
►
holding the accessory, spray the detergent by activating the lever (Fig. S, ref. 2), and rub the floor with
the bristles (Fig. S, ref. 3) to remove the dirt.
►
check at all times that the clean water tank is not empty, as operating the pump without water may cause
irreparable damage.
►
turn on the suction and vacuum up the water, sliding the squeegee (Fig. S, ref. 3) across the floor using
the part with rubber strips.
►
after having washed the area using the accessory, switch the machine off.
GB
29
Publicidad
