Publicidad
Idiomas disponibles
Idiomas disponibles
Refer to Figures 1 and 2.
Check for shipping damage. If damage has occurred, a claim
must be filled with carrier. Check for completeness.
Immediately
report missing parts to dealer.
The grinder comes assembled as one unit. Additional parts
which need to be fastened to grinder, should be located and
accounted for before assembling.
A Abrasive and aluminum disc with set screw
B Disc guard
C Disc dust chute
D Disc with attached trunnions
E Work stop
F Belt table assembly
G Belt dust chute
H Miter gauge assembly
Parts bag includes: two handles, three 1A-20 x W' washer
head screws, one 10-1.50 x 25mm socket head bolt, three
lOmm flat washers, and four #10-24 x 3/8"washer head
screws.
G
B
H
Figure 1 - Unpacking Sander
The stand comes unassembled
and packed along with the
sander in the same box. Locate and identify all parts before
attempting assembly (Refer to Figure 2).
CAUTION:
Do not attempt assembly if parts are missing.
Follow assembly instructions. Use parts list to order replace-
ment parts.
1 Top Frame (4)
2
Brace (4)
3
Leg (4)
4
Rubber foot (4)
5
8/18-18 V2" Carriage bolt (24)
6
8/18"-18Washer Head Hex nut (24)
7
8-1.25 x 50mm Hex head bolts (4)
8
8-1.25mm Hex nuts (4)
5
Figure 2 - Unpacking
Stand
6
8
7
CAUTION:
Do not attempt assembly if parts are missing.
Use this manual to order replacement parts.
TOOLS
NEEDED
While sanding or adjusting your belt and disc sander/grinder,
you will need the following tools:
• 10 and 17mm Wrench
• 2.5, 3, 4, 5, 6 and 8mm Hex wrenches
• Combination Square
• Phillips screwdriver
ASSEMBLE
DISC TABLE
Refer to figure 9, page 10.
• Attach disc guard to end shield (Key No. 23) using three
washer head screws (Key No. 27).
• Remove tape from key and armature (Key Nos. 21 and 20).
Slide aluminum disc with abrasive (Key Nos. 29 and 30)
onto armature with groove in disc aligned with key in arma-
ture.
• Slide disc dust chute (Key No. 28) onto disc guard from
below the 9" disc with exhaust port to rear of tool. Secure
dust chute to disc guard with two washer head screws (Key
No. 25).
• Slide disc table with attached trunnions (Key Nos. 32
through 35) onto the raised bosses on each side of disc
guard. Mount two handles and flat washers (Key Nos. 36
and 37) through trunnions into threaded holes on each side
of disc guard.
• Locate table in desired position and secure with handles.
• Be sure the gap between the disc and disc table is 1A8" o r less.
• If an adjustment is necessary, loosen set screw (Key No.
31) in aluminum disc through the opening at top-rear of
disc guard. Position disc 1/1_" o r less from edge of table.
Secure disc with set screw.
ASSEMBLE
BELT TABLE
Refer to figure 9, page 10.
• Slide belt table assembly (Key No. 46) into trunnion groove
in pivot bracket (Key No. 38). Mount using socket head bolt
and flat washer (Key Nos. 41 and 37). Locate table in
desired position. Be sure that gap between belt table and
belt is 1/18" o r less. Tighten bolt securely.
3
Publicidad
