Publicidad
Idiomas disponibles
Idiomas disponibles
CARE AND MAINTENANCE
Occasional care and maintenance of the unit and the software
are needed to optimize the performance of your unit,
To clean the cabinet
Use a soft and dry cloth.
If the surfaces are extremely
dirty, use a soft cloth lightly
moistened with mild detergent solution.
Do not use strong
solvents, such as alcohol, benzine or thinner as these could
damage the finish of the unit.
To clean the heads and tape paths
After every 10 hours of use, clean the heads and tape paths
with a head cleaning cassette or cotton swab moistened with
cleaning fluid or denatured alcohol. (These cleaning kits are
commercially available.)
When cleaning with a cotton swab, wipe the recording/playback
head, erasure head (deck 2 only), capstans, and pinchro(lers.
r
\
I
playback ~ead
Cotton swab
I
After cleaning the heads and tape paths with a liquid head
cleaning, cassette or a moistened swab, wait until the cleaned
parts are completely dry before inserting the tapes.
To demagnetize
the heads
The heads may become magnetized after long-term use. This
may narrow the output range of recorded tapes and increase
noise. After 20 to 30 hours use,' demagnetize the heads with
any commercially available demagnetizer.
Care of discs
QWhen a disc becomes dirty, wipe the disc from the center out
with a cleaning cloth.
After playing a disc, store the disc in its case. Do not leave the
disc in places that are hot or humid.
Care of tapes
Store tapes in their cases after use.
Do not leave tapes near magnets, motors, television sets, or
any source of magnetism. This will downgrade the sound quality
and cause noise.
Do not expose tapes to direct sunlight, or leave them in a car
parked in direct sunlight.
TROUBLESHOOTING
GUIDE
If the unit fails to perform as described in these Operating
Instructions, check the following guide.
IGENERAL
'There is no sound.
(I IS the AC cord connected
prOPE!rly?
II
Is there a bad connection? (+ page 3)
I, There may be a short circuit in the speaker terminals.
+ Disconnect
the AC cord, then correct
the speaker
connections.
{, Was an incorrect function button pressed?
Sound is emitted from one speaker only.
I>
IS the
other speaker disconnected?
'The output sound is not stereo.
II IS the Karaoke function turned on? (+ page 19)
An erroneous
display or a malfunction
occurs.
+ Reset the unit as stated below.
'TUNER SECTION
'There is constant, wave-like static.
I) IS the antenna connected prOperly? (+ Page 3)
I) 1sthe signal weak?
+ Connect an outdoor antenna.
"Thereception contains noise interferences
or the sound
is distorted.
II I.Sthe system picking Up external noise or multipath distortion?
+ Change the orientation of the antenna.
+ Move the unit away from other electrical appliances.
ICASSETTE DECK SECTION
'The tape does not run.
It IS deck 2 in pause mode? (+ page 13)
'The sound is off-balance
or not adequately
high.
,) IS the playback head dirty? (+ page 24)
Recording is not possible.
,. ls the erasure
prevention
tabon the
tape broken off? (+ page
14)
DIs the recording head dirty? (+ page 24)
Erasure is not possible.
', IS the erasure head dirty? (+ page 24)
10 Is a metal tape being used?
High frequency
sound is not emitted.
~ Isa tape recorded without Dolby NR played back with the Dolby
NR system operating? (+ page 13)
~ Is the recording/playback head dirty? (+ page 24)
CD PLAYER SECTION
'The CD player does not play.
oIs the disc correctly inserted? (+ page 11)
c Is the disc dirty? (+ page 24)
~ Is the lens affected by condensation?
+ Wait approximately one hour and try again.
To reset
If an unusual condition occurs in the display window or the
cassette decks, reset the unit as follows.
1
Press the POWER button to turn off the power.
2 Press the POWER button to turn the power back on while
pressing the
CLEAR button, Everything stored in memory
after purchase is canceled.
If the power cannot be turned off in step 1 because of a malfunction,
reset by disconnecting the AC cord, and connect it again. Then
repeat step 2.
ENGLISH
24
Publicidad
