Publicidad
Idiomas disponibles
Idiomas disponibles
TROUBLESHOOTING
PROBLEM
Sanding disc or belt
The wood gets
covered with grease.
burnt during
sanding.
Excessive pressure on workpiece.
Loosely mounted tool.
Strong
Defective tool.
vibrations.
Spindle knocks.
PARTS LIST
I.D. No.
D e s c r i p t i o n
1
Base
2
Baseplate
3
Fixed table
4
Movable table
5
Axis pin
6
Philips screw assembly M5 x 12
7
Rubber ring
8
Dust port
9
Switch
10 Motor
11 Bearing
12 Pressing plate
13 Philips screw ST4.2 x 12
14 rubber blanket
15 Felt blanket
16 Shaft sleeve
17 Spindle
18 69 teeth synchronous belt wheel
19 Press plate with wheel
20 Circlip for shaft
21 70 teeth synchronous belt wheel
22 Spring backed plate
23 Backpanels
24 Screw
25 Motor wheel
26 Synchronous belt
27 Synchronous belt
28 Tightening rack assembly
29 Tightening wheel assembly
30 Nut
31 Connector
32 Sand cylinder pressing plate
33 Sand cylinder roller
POSSIBLE CAUSE
Qty.
I.D. No.
1
34 Screw, spring washer and flat washer 8
1
35 Foot
1
36 Cable joint
37 Half round key
1
2
38 Install wire fixing button
12
39 Lead clip
40 Sand cylinder roller
1
1
41 Sand cylinder roller
1
42 Sand cylinder roller
1
43 13 mm Work table plate
2
44 38 mm Work table plate
45 26 mm Work table plate
2
32
46 19 mm Work table plate
2
47 51 mm Work table plate
2
48 Sand cylinder
1
49 Sand cylinder
1
50 Sand cylinder
1
51 Sand cylinder
2
52 Sand cylinder
53 Washer
2
1
54 Nut
2
55 Wrench
1
56 Power cord
4
57 Spring
58 Axle sleeve
1
1
59 Left table support
1
60 Right table support
61 Belt work table plate
1
1
62 Nut
1
63 Screws
1
64 Tension handle
1
65 Leaf spring
66 Screw, spring washer and flat washer 2
1
Replace disc or belt.
Reduce pressure on workpiece.
Tighten tool.
Change tool.
Repair at a service-station.
D e s c r i p t i o n
10
HELP
Qty.
I.D. No.
D e s c r i p t i o n
67 Fixed the slider
4
68 Screws
1
69 Limit board
1
70 Index plate handle
2
71 Belt support
1
72 Support plate
1
73 Guide frame
1
74 Sand belt tension handle
1
75 Driven shaft
1
76 Drive roller
1
77 Driven roller
1
78 Sand belt adjusting handle
1
79 Washer
1
80 Sand belt lock handle
1
81 Deep groove ball bearing
1
82 Circlip for shaft
1
83 Deep groove ball bearing
1
84 Screws M5 x 35
1
85 Type I hex nut -M5
1
86 Big washer -5
1
87 Philipps screws M5 x 16
1
88 Regulating spring
1
89 Extension spring
1
90 Flat washer -5
1
91 Rubber washer
1
92 Philipps screws M5 x 8
1
93 Belt
1
94 Miter rods
2
95 Index plate
2
96 Big washer -6
2
97 Handle M6 x 16
1
Qty.
1
2
1
1
1
1
1
1
1
1
1
1
3
1
2
1
2
5
5
2
1
1
1
2
1
2
1
1
1
1
1
Publicidad
