IKRA ICMS 2011 Instrucciones De Manejo página 28

EN ENGLISH
Guide Bar
Generally, guide bars with small radius tips have
somewhat lower potential for kick-back. You should use a
guide bar and matching chain which is just long enough
for the job. Longer bars increase the risk of loss of control
during sawing. Regularly check the chain tension.
Additional safety warnings
Some regions have regulations that restrict the use of the
machine. Check with your local authority for advice.
Never allow children or people unfamiliar with the
instructions to use the machine. Local regulations may
restrict the age of the operator.
Ensure before each use that all controls and safety
devices function correctly. Do not use the machine if the
"off" switch does not stop the motor.
Do not wear loose fitting clothing, short trousers, or
jewellery of any kind.
Secure long hair so it is above shoulder level to prevent
entanglement in moving parts.
Beware of thrown, flying, or falling objects. Keep all
bystanders, children, and animals at least 15 m away from
the work area.
Do not operate in poor lighting. The operator requires a
clear view of the work area to identify potential hazards.
Use of hearing protection reduces the ability to hear
warnings (shouts or alarms). The operator must pay extra
attention to what is going on in the work area.
Operating similar tools nearby increases both the risk
of hearing injury and the potential for other persons to
enter your work area.
Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance and can
increase the risk of kickback.
Keep all parts of your body away from any moving part.
Inspect the chain saw before each use. Check for correct
operation of all controls. Check for loose fasteners, make
sure all guards and handles are properly and securely
attached. Replace any damaged parts before use.
Do not modify the machine in any way or use parts
and accessories which are not recommended by the
manufacturer.
WARNING
If the machine is dropped, suffers heavy impact or
begins to vibrate abnormally, immediately stop
the machine and inspect for damage or identify
the cause of the vibration.Any damage should be
properly repaired or replaced by an service station.
Residual Risk
• Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual
risk factors. The following hazards may arise in use and
the operator should pay special attention to avoid the
following:
28
• Injury caused by vibration
Always use the right tool for the job. Use designated
handles. Restrict working time and exposure.
• Damage to hearing due to exposure to noise
Wear hearing protection and limit exposure.
• Injury caused by contact with exposed saw teeth of the chain
• Injury caused by thrown-out pieces of the workpiece
(wood chips, splinters)
• Injury caused by dust and particles
• Injury to the skin caused by contact with lubricants
• Parts ejected from the saw chain (cutting/injection hazards)
• Unforeseen, abrupt movement, or kickback of the guide
bar (cutting hazards)"
Risk Reduction
• It has been reported that vibrations from handheld
tools may contribute to a condition called Raynaud's
Syndrome in certain individuals. Symptoms may inclu-
de tingling, numbness, and blanching of the fingers,
usually apparent upon exposure to cold. Hereditary
factors, exposure to cold and dampness, diet, smoking
and work practices are all thought to contribute to the
development of these symptoms. There are measures
that can be taken by the operator to possibly reduce
the effects of vibration:
• Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm.
• After each period of operation, exercise to increase
blood circulation.
• Take frequent work breaks. Limit the amount of expo-
sure per day.
• Protective gloves available from professional forestry
equipment dealers are specifically designed for use
with hand saws and chainsaws and provide protection,
a secure grip and also reduce the effect of the vibrating
handle. These gloves should comply with EN 381-7 and
be CE marked.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor.
WARNING
Injuries may be caused, or aggravated, by
prolonged use of a tool. When using any tool for
prolonged periods, ensure you take regular breaks.