Husqvarna ST 324 Manual De Usuario página 14

230 V A.C. three-wire grounded system.
If you are uncertain, ask a licensed
electrician.
1. Insert the ON/OFF key (A) into the ignition slot
until it clicks. Do not turn the key. (Fig. 60)
2. Slide the control lever (B) to the ON position.
3. Put the throttle control (C) to the FAST position.
a) If the engine is cold, slide the choke lever (D)
to the FULL position.
4. Push the primer (E) three times.
CAUTION:
the engine. It can prevent the engine
from starting. If the engine is over
primed, wait a few minutes before
trying to start and do not push the
primer.
5. Connect the extension cord to the connector on
the engine (F).
6. Connect the other end of the extension cord into
a three-hole grounded 230 V A.C. receptacle.
7. Push the electric start button (G) until the engine
starts.
CAUTION:
engine more than five continuous
seconds between each time you try
to start. Wait 1 minutes between
each try.
8. If the choke was used to start the engine, release
the electric start button and slowly move the
choke (D) to the OFF position.
9. Disconnect the extension cord from the
receptacle first and then from the engine.
10. Run the engine 2-3 minutes at idling speed
before you start to throw snow.
To start the engine, electric start
WARNING:
V A.C. electric starter. Do not use the
electric starter if your house is not a
120 V A.C. three-wire grounded system.
Serious personal injury or damage to
the product could occur. The electric
starter has a three-wire power plug, and
is designed to use 120 V A.C. household
current. Make sure that your house is a
120 V A.C. three-wire grounded system.
If you are uncertain, ask a licensed
electrician.
1. Insert the ON/OFF key (A) into the ignition slot
until it clicks. Do not turn the key. (Fig. 60)
2. Turn the fuel ON/OFF switch (B) to the ON
position.
3. Put the throttle control (C) to the FAST position.
14
Do not over prime
Do not crank the
The product has a 120
a) If the engine is cold, turn the choke (D) to the
FULL position.
4. Push the primer (E) three times.
CAUTION:
the engine. It can prevent the engine
from starting. If the engine is over
primed, wait a few minutes before
trying to start and do not push the
primer.
5. Connect the extension cord to the connector on
the engine (F).
6. Connect the other end of the extension cord into
a three-hole grounded 120 V A.C. receptacle.
7. Push the electric start button (G) until the engine
starts.
CAUTION:
engine more than five continuous
seconds between each time you try
to start. Wait 1 minute between each
try.
8. If the choke was used to start the engine, release
the electric start button and slowly move the
choke (D) to the OFF position.
9. Disconnect the extension cord from the
receptacle first and then from the engine.
10. Run the engine 2-3 minutes at idling speed
before you start to throw snow.
To operate the product
CAUTION:
snow or water to lubricate the auger
blades. Incorrect use can cause high
temperatures in the auger blades,
especially if the product is new. This can
cause damage to the auger blades and
scraper bar.
CAUTION:
drive or auger levers for an extended
period of time; this can lead to premature
wear or burning of the belts.
Note:
When both the drive engagement and auger
engagement are engaged, the drive engagement will
lock the auger engagement in position. Use the right
hand to control the snow discharge chute.
Note:
Do not change the speed when the drive
lever is engaged. This can cause damage to the
transmission.
1. To engage the auger blades, push the auger
engagement (A) to the handle to engage the
auger and throw snow. (Fig. 61)
Do not over prime
Do not crank the
Do not operate without
Do not partially engage
2081 - 003 -