Publicidad
Idiomas disponibles
Idiomas disponibles
Warning: Never carry out any assembly or adjustment operations with
the power supply connected to the mower. Always ensure that the power
button is in the off position and that the power plug is disconnected from
the extension cord.
Cleaning:
1. do not spray the appliance with water. Water ingress can damage
components such as the switch/plug and the electric motor.
2. clean the unit with a cloth, hand brush, etc.
Consultation with the Service is required:
(a) If the mower hits an object.
(b) If the engine stops suddenly
c) If the blade is bent (do not align!)
d) If the motor shaft is bent (do not align!)
It is recommended to replace the mower blade at the end of the mowing
season. Always have the mower blade replaced at an authorised service
centre (requires blade balance measurement).
An unbalanced blade causes violent vibration of the mower and a
risk of accident!
Checking the grass catcher box and any damaged parts
Check the grass tank for signs of wear at more frequent intervals.
Replace any worn or damaged parts.
Use only original spare parts for maintenance.
The component exposed to the heaviest wear is the blade. Check the
condition of the blade and its holder at regular intervals. When the blade
is worn, replace it. If there is excessive vibration of the mower, this is a
sign that the blade is not properly balanced or deformed due to impact. In
this case, replace the blade.
Storing the mower:
•
Disconnect the power cord.
•
Allow the engine to cool for about 30 minutes.
•
Check, repair or replace any power cable that shows signs of wear or
damage.
•
Tighten or replace worn, loose or damaged parts, and clean them
thoroughly.
•
Thoroughly clean the outside of the unit with a soft brush and cloth.
Do not use water, solvents or polishes. Remove all grass and dirt,
especially from the vents.
•
Turn the unit on its side and clean the blade and its guard. If blades
of grass are on or around the blade, remove them with a wooden or
plastic tool to protect the blade.
•
To protect the mower from rust, wipe all exposed metal parts with a
cloth soaked in oil or spray with a light grease.
•
Keep the mower and extension cord in a closed, dry place out of the
reach of children to prevent unauthorised use or damage.
•
Cover loosely with a tarpaulin for extra protection.
•
If transporting, remember to secure the unit correctly to the vehicle.
•
In order to reduce the storage space of the mower, the upper handle
can be folded down, as shown in Fig. B.
Note: Do not press down on the electrical cord when folding the handle.
Make sure it does not get stuck or entangled when folding or unfolding the
top handle.
PROBLEM SOLVING
Always pull the mains plug and wait for the blade to stop before
carrying out any maintenance or cleaning work.
Symptom
Possible problem
Power off
Power socket defective Use a working power socket
Extension cable
defective
Grass too tall
Device does
not work
Safety/overload
protection has been
activated
Extension cable
defective
The mower
The grass container is
runs
full.
intermittently
The internal wiring of
the mower is damaged
Solution
Switch on the power supply
Check, replace if damaged.
Increase cutting height
Allow to cool for a few
minutes and increase the
cutting height
Do not operate the switch
lever at this time, as this will
increase the reset time of the
safety guard
Check, replace if damaged
Empty the grass container.
Contact the service
Cutting height too low
Cutting blade jerks the
grass or does not cut
Mower does
not work
Underside of machine
properly
badly clogged
Blade mounted upside
down
Cutting blade blocked
Cutting blade
does not rotate
Blade nut/bolt loose.
Blade nut/bolt loose
Excessive
vibration/noise
Cutting blade defective Replace the blade
TECHNICAL SPECIFICATIONS
RATING DATA
Electric mower 59G475
Parameter
Supply voltage
Supply frequency
Rated power
No-load spindle speed
Degree of protection
Mowing diameter
Mowing height range
Number of cutting height positions
Grass catcher capacity
Protection class
Mass
Year of production
59G475 indicates both the type and the designation of the machine
NOISE AND VIBRATION DATA
Sound pressure level
Sound power level
Vibration acceleration values
Information on noise and vibration
The noise emission level of the equipment is described by: the emitted
sound pressure level Lp
A
measurement uncertainty). The vibrations emitted by the equipment are
described by the vibration acceleration value a
measurement uncertainty).
The sound pressure level Lp
vibration acceleration value a
measured in accordance with EN IEC 62841-4-3. The vibration level a
given can be used for comparison of equipment and for preliminary
assessment of vibration exposure.
The vibration level quoted is only representative of the basic use of the
unit. If the unit is used for other applications or with other work tools, the
vibration level may change. Higher vibration levels will be influenced by
insufficient or too infrequent maintenance of the unit. The reasons given
above may result in increased vibration exposure during the entire working
period.
In order to accurately estimate vibration exposure, it is necessary to
take into account periods when the device is switched off or when it
is switched on but not used for work. When all factors are accurately
estimated, the total vibration exposure may be significantly lower.
In order to protect the user from the effects of vibration, additional safety
measures should be implemented, such as cyclical maintenance of the
machine and working tools, securing an adequate hand temperature and
proper work organisation.
ENVIRONMENTAL PROTECTION
Electrically-powered products should not be disposed of with
household waste, but should be taken to the appropriate
facilities for disposal. Contact your product dealer or local
authority for information on disposal. Waste electrical and
electronic
substances. Equipment that is not recycled poses a potential
risk to the environment and human health.
10
Increase cutting height
Replace the blade
Clean the device
Fix the blade in the correct
position
Serious damage - contact
service recommended
Tighten the blade nut/bolt
Tighten the blade nut/bolt
230-240 V AC
Lp
= 85 dB(A) K= 3 dB(A)
A
Lw
= 94.5 dB(A) K= 1.84 dB(A)
A
a
= 3.02 m/s
h
and the sound power level Lw
h
, the sound power level Lw
A
given in these instructions have been
h
equipment
contains
environmentally
Value
50 Hz
2000 W
-1
3800 min
IPX4
430 mm
20-70 mm
6
45 l
II
15 kg
2023
2
2
K= 1.5 m/s
(where K denotes
A
(where K is the
and the
A
h
inert
Publicidad
