Publicidad
Idiomas disponibles
Idiomas disponibles
ELECTRICAL
SAFETY
Z_ WARNING:
Do not permit fingers
to touch the terminals
of plug when
installing or removing
the extension cord from the plug.
1. Double insulated tools are equipped with a polarized plug
(one blade is wider than the other and will require the use of a
polarized extension cord. The Chain Saw's plug will fit into a
polarized extension cord only one way. If the plug does not fit fully into
the extension cord, reverse the plug. if the plug still does not fit, obtain
a correct polarized extension cord. A polarized extension cord will require the use of a polarized
wall outlet. This plug will fit into the polarized wall outlet only one way. If the plug does not fit
fully into the wall outlet, reverse the plug. if the plug still does not fit, contact a qualified
electrician to install the proper outlet. Do not change or alter the equipment plug,
extension cord receptacle, or extension cord plug in any way.
2. Double insulation [] eliminates the need for the three-wire grounded power cord and
grounded power supply system. Applicable only to Class II (double-insulated)
tools.
This Chain Saw is a double insulated tool.
WARNING:
GFCI (Ground Fault Circuit interrupter) protection should be
provided on all circuits or outlets to be used for electric chain saws and lawn and
garden power tools. Receptacles are available having built=in GFCl protection and
should be used for this measure of protection.
,, Double insulation DOES NOT take the place of normal safety precautions when
operating
this tool.
,,Guard against electric
shock: Prevent
body contact
with grounded surfaces.
For example: metal pipes, wire fences.
3. BEFORE plugging in the tool, BE SURE that the outlet voltage supplied is within the voltage
marked on the tool's data plate. DO NOT use "AC only" rated tools with a DC power supply.
4. DO NOT expose tools to rain or wet conditions or use electric tools in wet or damp
locations. Water entering an electric tool will increase the risk of electric shock.
5. If operating an electric tool in damp locations is unavoidable, ALWAYS USE a
Ground Fault Circuit Interrupter to supply power to your tool. ALWAYS WEAR
electrician's
rubber gloves and footwear in damp conditions.
6. To reduce the risk of electric shock, use only with an extension cord intended for outdoor use,
such as an extension cord of cord type: SW-A, SOW-A, STW-A, STOW-A, SJW-A,
SJOW-A, SJTW-A. or SJTOW-A.
7. INSPECT tool cords for damage. Have damaged tool cords repaired at a Sears Service Center.
BE SURE to stay constantly aware of the cord location and keep it well away
from the cutting blade.
8. DO NOT abuse the extension cord. NEVER use the cord to carry the tool by or to
pull the plug from the outlet. Keep cord away from heat, oil, sharp edges or moving parts.
Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
EXTENSION
CORDS
Use a proper extension
cord. ONLY use cords listed by Underwriters Laboratories (UL).
Other extension cords can cause a drop in line voltage, resulting in a loss of power
and overheating of tool.
For this tool an AWG (American Wire Gauge) size of a least 14-gauge is recommended
for an extension cord of 25-ft. or less in length. Use 12-gauge for an extension cord
of 50-ft. Extension
cords 100-ft. or longer are not recommended.
6
EXTENSION CORDS cont.
Remember, a smaller wire gauge size has greater capacity than a larger number
(14-gauge wire has more capacity than 16-gauge wire; 12-gauge wire has
more capacity than 14-gauge). When in doubt use the smaller number.
Method of securing
extension
cord
Minimum guage for extension
cords
Volts
Total length of cord in feet
120V
25
50
100
150
240V
50
100
260
300
Ampe_re Rating
More
than
Not more
ttian
AWG
0-6
18
16
16
I
14
6 - '10
18
16
14
12
18 - 12
16
16
14
12
12 -
16
14
12
Not recommel'_ed
NOTE - Only the applical_e pa_s of the Tal_e need to be include_. For instance, a 120-volt product _
not
include the 240-volt h_r_J_
Z_ CAUTION:
Keep the extension cord clear of the work area. Position the cord so that it will
not get caught on bushes, hedges, tree trunks, lawnmowers or other obstructions
while you are
working with the Chain Saw.
WARNING:
Check extension cords before each use. if damaged replace immediately.
Never use tool with a damaged cord since touching the damaged area could cause electrical
shock, resulting in serious injury.
SAFETY SYMBOLS
FOR YOUR TOOL
The label
on your tool
may include
the following
symbols.
V................Volts
A................Amps
Hz .............. Hertz
W...............Watts
rnin ............ Minutes
"-4. ............Alternating current
..........Direct current
no ............ No-load speed
.../rain....... Revolutions or Strokes per minute
Z_ ............. Indicates danger, warning or caution.
It means attentio!! Your safety is
involved.
......... Tip contact may cause the guide
bar to move suddenly upward
and backwards, which may cause
serious injuryto user.
......... Contact of the guide bar tip with
any object should be avoided.
_'_
......... Read and follow all safety
precautions in the owner's manual
Failure to follow to instruction
could result in serious injury to user.
........ Do not expose to rain.
A
Remove plug from mains immediately
if the cable is damaged or cut.
......... Protective goggles/visor,
helmet & hearing protection.
(_
Gloves with saw protection.
......... Boots with saw protection,
steel-toe cap and non-slip sole.
I......... Wear dust mask.
_]
......... Do not use one handed when
operating the chain saw.
......... Always use two hands when
operating the chain saw.
.......... Class II construction,
Double-insulation.
When servicing,
use only identical replacement
parts.
........ The chain saw kickback angle
is 10 °, with a chain stop.
......... Correct Direction of Cutting-Teeth.
(_(X_:) ......... Chain Stop
Warning of danger from overhead
ebctfic-power lines.
7
Publicidad
