Publicidad
Idiomas disponibles
Idiomas disponibles
,...
The unit can be turned on at a specified
time every day with the
built-in timer.
Preparation
Make sure the clock is set correctly,
1
2
3
4
Press one of the function
buttons to select a
source.
*
If
TUNER/BAND is
pressed,
the band cannot be selected
in
this step,
Press TIMER
while pressing SHIFT on the remote
control so that G!)appears on the display.
Time and audio source name flash alternately.
@
Within 6 seconds, press+
or >>
to designate
the timer-on time, then press 11.
Pressing either button changes
both the hour and the minute.
Holding it down will vary the time rapidly by 10-minute
interval,
and pressing
it repeatedly
will vary by 1 minute interval.
Within 4 seconds, press +<
or >
to select the
duration for the timer-activated
period.
The duration
can be set between
5 and 240 minutes
in 5
minute steps.
The duration
will be automatically
set after 4 seconds.
It will
also be set if II is pressed
within 4 seconds
after step 4,
5
6
7
8
Adjust the volume.
a
The source sound will play at the volume level set in this step
when the power is turned on by the timer.
;..
If the volume
level is set to 17 or higher,
however,
it will
.j;~jl
automatically
be set to 16 when the power is turned on,
;;~$
?
.? ,
2~"
Prepare the source.
J::,. &
;g;;
To
listen to a CD,
load the disc to be played first on tray 1.
~~
8
'" '. ".
To
listen to a tape,
insert the tape into deck 1 or 2.
?.
To listen
to the radio,
tune in to a station.
d
Press POWER to turn off the power.
When the timer-on
time is reached,
the unit turns
on and
begins play with the selected
source.
Get ready for the tape function
or the timer
recording.
To
listen
to the tape, press b.
To record
the source,
press
on deck 1,
When the timer-on
time is reached,
the unit turns on and
begins
play with the selected
source,
While the timer is in
operation,
the display indication
is dimmer than usual,
m
You can change
the source
that was selected
in step
1 by
pressing
one of the function
buttons
before pressing
II in step
3.
The timer recording period and tape length
When the length of the tape to be recorded
is shorter
than the
timer recording
period,
on deck 1 is released
before the timer
is off.
When the tape length is longer than the timer recording
period,
is not released.
If
is not released
for a long time, the tape
in the deck may be damaged.
Press W+
to release
.
To check the timer setting
Press
TIMER
while pressing
SHIFT
on the remote control.
The selected
source, the timer-on
time, and the duration
for the
timer-activated
period will be displayed
for 4 seconds,
To change any of the previous setting
Carry out from step 1.
However,
if you do not change
the timer-on
time, in step 3 just
press II twice and continue
from step 4.
To cancel the timer standby mode temporarily
Press
TIMER
repeatedly
while pressing
SHIFT
on the remote
control to display "['{OFF.
To restore the timer standby
mode, press again to display ~,
Using the unit while the timer is set
You can use the unit normally
after setting the timer,
Before turning off the power, check whether the contents
in step
5 and 6 are set as you wish, turn off the power and carry out step
8 if necessary,
m
Timer playback
will not begin unless the power is turned off.
Connected
equipment
cannot be turned on and off by the built
in timer of this unit.
Use an external
timer.
ENGLISH
15
Publicidad
