Publicidad
EN
9. Keep a distance of 50mm between AIO 2400 and other objects.
10. During the operation of the solar energy system, avoid direct sunlight to prevent the AIO 2400 from
overheating. Do not place the AIO 2400 near any heat source.
11. Please install the product according to our user manual to avoid damage to the product or injury to other
people.
12. Do not use this product near strong static electricity or strong magnetic fields.
13. Do not place the equipment in an environment with flammable or explosive compounds, gas, or smoke.
Since AIO 2400 relies on the shell to dissipate heat, exposing the enclosure to excessive heat will lead to
damage.
14. To reduce risk of damage to the electric cords and connectors, pull the connectors rather than the cord
when disconnecting the product.
15. Do not use the product in excess of its output rating. Overloads may result in a risk of fire or injury to
persons.
16. Do not use any products or accessories that are damaged or modified. Damaged or modified batteries may
exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
17. Do not operate the product with a damaged cord or plug, or a damaged output cable.
18. Do not disassemble the product. Take it to a qualified service person when service or repair is required.
Incorrect reassembly may result in a risk of fire or electric shock.
19. Do not expose the product to fire or high temperatures.
20. Do not attempt to replace the internal components of the equipment by any unauthorized personnel. Have
servicing performed by a qualified repair person using only identical replacement parts. This will ensure that
the safety of the product is maintained.
21. AIO 2400 has a protection level of IP65, so the product cannot be immersed in liquids. If the product
accidentally falls into water during use, please place it in a safe and open area and stay away from it until it
is completely dry. The dried product should not be used again and should be properly disposed of according
to the disposal guidelines in this manual.
22. When charging a device, the product may feel warm. This is a normal operating condition and should not be
a cause for concern.
23. To reduce the risk of electric shock, unplug the power pack from the outlet before attempting any instructed
servicing.
24. When charging the internal battery, work in a well-ventilated area and do not restrict ventilation in any way,
as inadequate ventilation may cause permanent damage to the equipment.
25. Ensure before finishing installation that the solar cable and Microinverter cable to home grid are
disconnected.
26. Do not clean the product with harmful chemicals or detergents. Only clean the ports with a dry cloth.
27. Do not move or shake the unit while operating as vibrations and sudden impacts may lead to poor
connections to the hardware inside.
28. Ensure that AIO 2400 and the Microinverter are installed securely to avoid accidents and product damage
caused by falling.
29. In case of a fire, only a dry powder fire extinguisher is suitable for this product.
30. Servicing of batteries should be performed or supervised by personnel knowledgeable about batteries and
the required precautions.
1.2 FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1 ) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
2. Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
2
Publicidad
