Redarc TVMS Rogue Guia De Instalacion página 10

TECHNICAL SPECIFICATIONS
Specifications subject to change without notice.
GENERAL SPECIFICATIONS
Main Unit Dimensions
Main Unit Weight
Warranty
ELECTRICAL SPECIFICATIONS
Power Input
Supply Voltage
Supply Current Limit
Connector Housing
Connector Contacts
Output Channels
Number of Channels
Channel Current Limit
PWM Dimming Capable
Harness Connector
Connector Contacts
Protection
Output Overload Protection
Output Short Circuit Protection
Surge Protection
Reverse Polarity Protection
Switch Input Channels
Number of Switch Inputs
Switch Types Supported
Harness Connector
Connector Contacts
Sensor Input Channels
Number of Channels
Sensor Input Functions
Sensor Input Modes
Multi Point Calibration
Sensor Supply Voltage
Sensor Supply Current
Tank Sensors Supported
Harness Connector
Connector Contacts
THERMAL SPECIFICATIONS
Operating Temperature
Overtemperature Shutdown
10
250 × 130 × 25 mm /
9.8" × 5.1" × 1"
≈ 430 g / 1 lb
2 years
9–16 VDC ⎓
40 A
Molex 428160212
Molex 428150134
10
10 A
Yes, All Channels
Molex 039012100
Molex 457503111
Yes
Yes
Yes
Yes
8
Pushbutton or Rocker
Molex 430252400
Molex 430300001
2
Tank Level, Temperature,
DC Voltage
Voltage (0–32 V), Resistance
(0–1000 Ω)
Yes, up to 10 points
System Voltage + 0 V / –2 V
80 mA maximum
0–5 V, 0.5–4.5 V, 240–33 Ω,
0–190 Ω
Molex 430252400
Molex 430300001
−20°C to +70°C
−4°F to +158°F
Progressive Load Shedding
COMPLIANCE AND STANDARDS
Regulatory
Safety EN 61010.1
Environmental RoHS and REACH compliant
FEDERAL COMMUNICATIONS COMMISSION (FCC)
STATEMENT
Part 15.105 NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
ƒ Reorient or relocate the receiving antenna.
ƒ Increase the separation between the equipment and receiver.
ƒ Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
ƒ Consult the dealer or an experienced radio/TV technician for help
This device contains FCC ID: XPYNINAB1
Details of the Responsible Party:
REDARC Corporation
1701 Northwest Highway, Suite 100
Grapevine TX
76051
USA
Phone: +1 (704) 247 5150
INDUSTRY CANADA (IC) COMPLIANCE NOTICE
This equipment complies with IC RSS-102 radiation exposure limits
set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum
distance of 20 cm between the radiator and your body.
IC Radiation Exposure Statement:
This device complies with Industry Canada (IC) license-exempt RSS
standard(s). Operation is subject to the following two conditions.
1. This device may not cause interference.
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
This device contains IC: 8595A-NINAB1