Publicidad
Idiomas disponibles
Idiomas disponibles
Model: 6138
REGULATOR SAFETY
• Use this appliance, as purchased, only with gas and regulator/
valve assembly supplied� do NoT use quick connect fittings or
other add-ons�
• do NoT cross thread (force at an improper angle) the connection
between your lPG cylinder and regulator�
• If you can not connect the regulator, do NoT use the regulator�
Regulator must be replaced with a Blackstone approved model by a profession-
Regulator must be replaced with a Blackstone approved model by a profession-
ally licensed, authorized dealer.
ally licensed, authorized dealer.
CONNECT THE LPG CYLINDER
ONLY USE A 20 LB (9 KG) CYLINDER
Turn the control
STEP 01
knobs to oFF�
❶ ❶ ensure that the lPG cylinder
is oFF by turning the oPd hand
wheel clockwise to a full stop�
❷ ❷ Remove the safety cap from
the Type 1 valve outlet�
Hold the regulator in a
STEP 02
straight line with the Type 1 valve
outlet so as not to cross thread
the connection�
Center and insert the regu-
lator nipple into the Type 1
valve outlet�
Hand-tighten the coupling nut in
a clockwise direction�
(do NoT use tools to connect�)
If connection cannot be completed,
If connection cannot be completed,
disconnect regulator and repeat this
disconnect regulator and repeat this
step.
step.
Set the lPG cylinder into
STEP 03
the propane cabinet�
The safety relief valve must face
away from the user while the
appliance is in use�
Use an lPG cylinder retention
system to prevent the cylinder
from tipping over�
The cabinet CAN NoT store 2 or
more gas cylinders�
BLACKSTONEPRODUCTS.COM/SUPPORT
❶ ❶
❷ ❷
Coupling nut
Coupling nut
Regulator nipple
Regulator nipple
LPG CYLINDER ENCLOSURE
CONSTRUCTION
A: A: 4x6 in (10x15 cm) vents at bottom,
4x6 in (10x15 cm) vents at bottom,
and both sides of cabinet.
and both sides of cabinet.
B: B: Plenum wall to separate the lPG
Plenum wall to separate the lPG
cylinder compartment.
cylinder compartment.
C: C: lPG cylinder access door.
lPG cylinder access door.
B B
C C
A
A
USING YOUR BLACKSTONE
IF GREASE OR OTHER HOT MATERIAL DRIPS ONTO VALVE, HOSE OR
REGULATOR:
Turn off gas supply immediately�
STEP 01
determine the cause and correct it�
STEP 02
Clean and inspect valve, hose and regulator�
STEP 03
Perform a leak test�
STEP 04
LEAK TEST: VALVES, HOSE & REGULATOR
Turn the control knobs to oFF�
STEP 01
Connect the regulator to the lPG cylinder�
STEP 02
Completely open the lPG tank by turning the oPd hand
STEP 03
wheel counterclockwise�
• If you hear a rushing sound, turn gas off immediately� There is a
major leak at the connection�
• Immediately close the lPG cylinder by turning the oPd hand wheel
clockwise and re-tighten connections� If leaks cannot be stopped
do NoT TRY To RePAIR�
Use a clean paintbrush
STEP 04
to brush a 10�90 mild soap and
water solutionn onto joint areas
of valves and regulator�
(Indicated by arrows in figure 02.)
(Indicated by arrows in figure 02.)
• leaks are indicated by
growing bubbles�
• Immediately close the lPG
cylinder by turning the oPd
hand wheel clockwise and
re-tighten connections�
If leaks cannot be stopped, DO NOT try to repair.
Regulator must be replaced with a Blackstone approved
model by a professionally licensed, authorized dealer.
DISCONNECTING THE LPG CYLINDER
ensure that the control knobs are turned to oFF�
STEP 01
❶ ❶ ensure that the lPG cylinder
is oFF by turning the oPd hand
wheel clockwise to a full stop�
❷ ❷ Turn the coupling nut count-
er-clockwise by hand to remove
the regulator� (do NoT use tools
to disconnect�)
Place dust cap on lPG
STEP 02
A A
cylinder valve outlet whenever
cylinder is not in use�
only install the type of dust cap on
only install the type of dust cap on
cylinder valve outlet that is provided
cylinder valve outlet that is provided
with the cylinder valve. other types of
with the cylinder valve. other types of
caps or plugs may result in leakage of
caps or plugs may result in leakage of
propane.
propane.
| OWNER'S MANUAL
figure 02
figure 02
WARNING
❶ ❶
❷ ❷
11
Publicidad
