Publicidad
Idiomas disponibles
Idiomas disponibles
OWNER'S MANUAL | USING YOUR BLACKSTONE
IGNITIoN INSTRUCTIoNS
2. BATTERY POWERED ELECTRIC IGNITION
1. CHECK VALVES
ensure gas is off at the supply shut off valve before checking
appliance valves�
Insert one (1) AA
STEP 01
Turn all knobs to the ❶ ❶ oFF position�
STEP 01
battery (not included) under the
battery cap�
Push in knob and release� Knob should spring back�
STEP 02
Screw the cap into place over the
If knobs do NoT
If knobs
do NoT spring back, replace valve assembly before using appliance.
spring back, replace valve assembly before using appliance.
positive terminal�
Rotate knob to loW then turn back to oFF� Knob should
STEP 03
turn smoothly�
Turn gas oN by turning
STEP 02
the gas cylinder handwheel
counterclockwise 1 to 3 turns�
STEP 03
❶ ❶ Push the control knob in to
start gas flowing�
❷ ❷ Turn the control knob
counter-clockwise to activate
the starter�
❸ ❸ Check flame and adjust the
temperature to desired level�
3. ALWAYS CHECK BURNER FLAME BEFORE USE.
light burners and rotate knobs from HIGH to loW�
STEP 01
look below the cooking surface to view burners� When knob
STEP 02
is at HIGH, flames should be larger than when knob is at loW�
HEALTHY FLAME PATTERN
❶ ❶
❷ ❷
❸ ❸
❶ ❶
Flickers of yellow color.
Flickers of yellow color.
❷ ❷
dark blue color.
dark blue color.
❸ ❸
Vibrant blue.
Vibrant blue.
12
3. ALWAYS CHECK BURNER FLAME BEFORE USE.
Clean the battery and appliance
Clean the battery and appliance
contacts prior to battery installation.
contacts prior to battery installation.
1 to 3 turns
1 to 3 turns
❶ ❶
❷ ❷
❸ ❸
YELLOW OR IRREGULAR
If there is a sudden drop or low
If there is a sudden drop or low
flame issue, please reference the
flame issue, please reference the
Troubleshooting chapter.
Troubleshooting chapter.
2. ELECTRIC IGNITION
2. BATTERY POWERED IGNITION
do NoT lean over the appliance while lighting�
Make sure the appliance is plugged in�
Insert one (1) AA
STEP 01
battery (not included) under the
Press the oN button�
STEP 01
ignitor button�
(optional: Turn the dimmer
Screw the button into place over
until it clicks to turn off the
the positive terminal�
puddle lights�)
STEP 02
Turn gas oN by turning
STEP 02
❶ ❶ Push the control knob in to
the gas cylinder handwheel
start gas flowing� (WHITE)
counterclockwise 1 to 3 turns�
❷ ❷ Turn the control knob
counter-clockwise to activate the
starter� (FLASHING BLUE)
❸ ❸ Check flame and adjust
STEP 03
the temperature to desired
❷ ❷ Push and hold the ignitor button�
level� (ORANGE)
❸ ❸ Push and turn the control knob counter-clockwise to HIGH�
(Release the ignitor button when the burner lights�)
Note: If the magnet in the knob is disconnected, the indicator light
❹ ❹ Adjust the temperature to desired level�
will be orange� If the knob arrow is facing UP, gas is not flowing�
❶ ❶
❸ ❸
❹ ❹
If burner does not ignite with open gas supply valve, gas
will continue to flow out of burner and could accidentally/
inadvertently ignite with risk of injury.
If ignition does not occur in 5 seconds:
1. Turn the burner control knob OFF.
2. Wait 5 minutes.
3. Repeat the lighting procedure.
If burner does not ignite, please reference the Troubleshooting chapter.
If burner does not ignite, please reference the Troubleshooting chapter.
Model: 6138
Clean the battery and appliance
Clean the battery and appliance
contacts prior to battery installation.
contacts prior to battery installation.
❶ ❶
1 to 3 turns
1 to 3 turns
❷ ❷
❸ ❸
❷ ❷
WARNING
BLACKSTONEPRODUCTS.COM/SUPPORT
WARNING
Publicidad
