Publicidad
Idiomas disponibles
Idiomas disponibles
Do not use the product if the muffler is missing or
defective. A defective muffler increases the noise level
and the risk of fire.
WARNING:
hot during and after use and when the
engine operates at idle speed. Be careful
near flammable materials and/or fumes to
prevent fire.
Fuel safety
WARNING:
instructions that follow before you use the
product.
•
Do not start the product if there is fuel or engine oil
on the product. Remove the unwanted fuel/oil and let
the product dry.
•
If you spill fuel on your clothing, change clothing
immediately.
•
Do not get fuel on your body, it can cause injury. If
you get fuel on your body, use soap and water to
remove the fuel.
•
Do not start the product if the engine has a leak.
Examine the engine for leaks regularly.
•
Be careful with fuel. Fuel is flammable and the fumes
are explosive and can cause injuries or death.
•
Do not breathe in the fuel fumes, it can cause injury.
Make sure that there is a sufficient airflow.
•
Do not smoke near the fuel or the engine.
•
Do not put warm objects near the fuel or the engine.
•
Do not add the fuel when the engine is on.
•
Make sure that the engine is cool before you refuel.
•
Before you refuel, open the fuel tank cap slowly and
release the pressure carefully.
•
Do not add fuel to the engine in an indoor area. Not
sufficient airflow can cause injury or death because
of asphyxiation or carbon monoxide.
To assemble the handle
1. Push the screw (A) through the handle (B), the
plastic washer (C) and the handle support bracket
(D). (Fig. 16)
2. Tighten the nut (E) fully.
3. Push the screw (F) thrugh the washer (G) and the
handle support bracket.
4. Tighten the knob (H) fully.
5. Align the holes in the handlebar with the holes in the
lower handle and attach the screws, washers and
knobs. Tighten the knobs fully. (Fig. 17)
6. Attach the cables to the handle with the cable
holders. (Fig. 18)
10
The muffler becomes very
Read the warning
Assembly
•
Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
•
Move the product a minimum of 3 m / 10 ft from the
position where you filled the tank before a start.
•
Do not fill the fuel tank fully. Heat causes the fuel to
expand. Keep a space at the top of the fuel tank.
Safety instructions for maintenance
WARNING:
instructions that follow before you use the
product.
•
The exhaust fumes from the engine contain carbon
monoxide, an odourless, poisonous and very
dangerous gas. Do not start the engine indoors or in
closed spaces.
•
Before you do the maintenance on the product, stop
the engine and remove the ignition cable from the
spark plug.
•
Use protective gloves when you do maintenance on
the cutting equipment. The blade is very sharp and
cuts can easily occur.
•
Accessories and changes to the product that are not
approved by the manufacturer, can cause serious
injury or death. Do not change the product. Always
use accessories that are approved by the
manufacturer.
•
If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases.
•
Only do the maintenance as given in this owner's
manual. All other servicing must be done by an
approved Husqvarna service agent.
•
Let an approved Husqvarna service agent do
servicing on the product regularly.
•
Replace damaged, worn or broken parts.
Note:
Make sure that the tension in the cables is
not too high. A too high tension can cause damage
to the cable if the handle is folded to transport
position.
7. Put the cables around the hook at the bottom of the
handle. (Fig. 19)
To adjust the handle height
1. Loosen the lower knobs. (Fig. 20)
2. Remove the knob, washer, and screw on the left and
the right side.
3. The handle can be set to 2 different heights. Put the
screw in one of the 2 holes on the left and the right
side. (Fig. 21)
Read the warning
1562 - 002 - 29.10.2021
Publicidad
