Publicidad
Idiomas disponibles
Idiomas disponibles
ASSEMBLY
Read and follow the assembly and adjustment
instructions for your snow thrower'. All fasteners
are in the parts bag. Do not discard any parts or
matedal until the unit is assembled.
,_
WARNING:
Before doing any
assembly or maintenance to the
snow thrower,
remove the wire
from the spark plug.
NOTE: In this instruction
book, left and right
describe
the location
of a part from the oper-
ator's position behind the unit.
NOTE: Torque is measured in foot pounds
(metric
N.m). This measurement
describes
how tight a nut or bolt must be. The torque is
measured
with a torque wrench.
NOTE: Illustrations
begin on page 3.
Tools Required
1
Knife
1
Pliers
How
To Remove
The Snow
Thrower
From
The Carton
1. Locate all parts that are packed separately
and remove from the carton.
2. Remove and discard the packing material
from around the snow thrower.
3. Cut down all four corners of the cadon and
lay the side panels flat.
4. Hold onto the lower handle and pull the snow
thrower off the carton.
CAUTION:
DO NOT back over cables.
5. Remove the packing material from the han-
dle assembly.
How
To Assemble
The Handle
1. Remove the packing material from the upper
and lower handles.
2. (Figure 1) Loosen the knobs (1) on each
side of the handle (2).
3. Raise the upper handle (2) to the operating
position.. Hold the upper handle (2) apart to
prevent scratching the lower handle.
NOTE: Make sure the cables are not
caught
between the upper and lower han-
dle.
4. Tighten the knobs (1).
5. (Figure 2) Cut and discard the cable tie (3)
from the lower end of the chute control rod
(4).
6. Turn the chute deflector
(5) around toward
the front of the snow thrower.
How To Assemble
The Lower
Chute
(Figure
3)
For shipping purposes, some models are
shipped with the rear nut and bolt removed from
the lower chute (3). If the lower chute is not at-
tached, assemble as follows.
1. Use the bolt (1) and nut (2) found in the
parts bag to attach the lower chute (3).
2. Tip the lower chute (3) backward until the
hole in the chute ring is aligned with the hole
in the lower chute (3).
3. Attach the lower chute (3) with bolt (1) and
nut (2). Make sure the nut (2) is tight.
How To Assemble
The Chute
Control
Rod (Figure
4)
1. Remove the cotter pin (f), fiat washer
(2),
and wave washer
(3) from the end of the
chute control
rod (4). DO NOT DISCARD.
2. Mount the end of the chute control
rod (4)
through the hole in the control rod bracket
(5). Make sure the worm gear (6) is aligned
with the notches
(7) in the discharge
chute
(8).
3. Fasten the chute control rod (4) to the con-
trol rod bracket
(5) with cotter
pin (1), fiat
washer (2), and wave washer (3).
4. Rotate the chute control rod (4) clockwise
and counterclockwise.
Make sure the dis-
charge chute (8) rotates freely.
How To Prepare
The Engine
A
WARNING:
Follow the engine
manufacturer's
instructions for the
_U_
type of fuel and oil to use. Always
use a safety fuel container. Do not smoke
when adding the fuel mixture to the engine.
When inside an enclosure, do not fill the
fuel tank. Before you add the fuel mixture,
stop the engine. Let the engine cool for
several minutes.
See the engine manufacturer's
instructions for
the type of fuel and oil to use. Before you use
the unit, read the information on safety, opera-
tion, maintenance,
and storage.
How To Mix The Fuel Mixture
The two cycle engine, used on this snow throw-
er', requires a mixture of gasoline and oil for lu-
ENGL/SH
brication of the bearings and other moving pads.
The correct fuel mixture ratio is 50:1 (2.6 oz. oil
per one gallon of gas - see the Fuel Mixture
Chad). Gasoline and oil must be pre-mixed
in a
clean gasoline container. Always use fresh,
clean, unleaded gasoline.
FUEL MIXTURE CHART (mixture
50:1)
I
U.S.
I
IMPERIAL
I
SL (Metric
I
Mix gasoline and oil as follows:
1. Pour one (1) U.S. quart of fresh, clean, un-
leaded automotive gasoline into a one gallon
size gasoline container'.
2. Add 2.6 ounces of clean, high quality, two-
cycle oil to the gasoline container.
IMPORTANT: Do not use outboard motor
oil or multi-viscosity
oils,such as 10W-30
or 10W_40.
3. Install the fuel cap onto the gasoline contain-
er. Vigorously shake the gasoline container
to mix the oil with the gasoline.
4. Add an additional three (3) U.S. quarts of
gasoline to the gallon container. Again shake
the gasoline container.
Before
You Operate
Before you operate your new snow thrower,
please review the following checklist:
•
Make sure all assembly instructions
have
been completed.
•
Make sure the discharge chute rotates freely.
•
Make sure that no loose parts remain in the
carton.
As you learn how to propedy use the snow
thrower, pay extra attention to the following im-
podant items.
•
Make sure the fuel tank is filled with the
correct mixture of gasoline and oil.
•
Become familiar with the location of all
controls and understand their function.
•
Before starting the engine, make sure all
controls operate correctly.
Do not fiII the fuel tank with gasoline that does not have oil mixed in it. Shake the
gasoline container before each filling of the fuel tank.
OII
Add more gas
(2.6 oz[
Shake Can
(3 U. S. Quarts)
I U.S. Gallon container
F-001023M
g
Publicidad
