Use Limitations - STAYER WELDING AS-0 Manual De Instrucciones

INDEX
1. Part List ................................................................... 14
2. Spares...................................................................... 14

3. Use limitations ........................................................ 14

4. Characteristics........................................................ 14
5. Specifications ......................................................... 15
6. User instructions .................................................... 15
6.1. Adjusting the mask to user ..............................................
6.2. Adjusting protection angle ...............................................
6.3. Adjusting sensibility .........................................................
6.4. Adjusting wait time ...........................................................
6.5. Setting grinding............................................................... .
7. Maintenance ............................................................ 16
7.1. Cleaning and storage ......................................................
7.2. Replacing protective lenses.............................................
7.3. Replacing exterior protection. ..........................................
7.4. Replacing interior protection ............................................
7.5. Replacing harness .......................................................... .
7.6. Replacing filter .................................................................
7.7. Guarantee....................................................................... .
8. Inspection................................................................ 17
9. Declaration of conformity ...................................... 18
1. PART LIST Fig.1
1. Filter support.
2. Interior protective lens.
3. Fixed/automatic filter.
4. Protection angle adjustment knob.
5. Frame holding screw.
6. Exterior protective lens.
7. Humidity textile band.
8. Harness height adjustment band.
9. Work angle adjustment deck.
10. Harness head size adjustment knob.
11. Retention bolt for work angle adjustment deck nº9.
12. Harness to helmet retention screw.
13. Harness to helmet screw retention knob.
14. Transparent Protector (Trabajos of annoyed)
15. Sensitivity adjustment to dark
16. Setting expected to clear
17. Adjust function welding / grinding
Protect this manual and have it available to the
user.
Read and understand completely this manual
before using this product.
2. SPARES
FIG. 6.
GS-1B 4020.20
AS-1B
4020.6
AS-0
4020.37
AS-1C
4020.36
Do not use any solder equipment without prior
training.
2. 8.
4020.16 4020.7 4020.16
4020.13 4020.7 4020.28
4020.39 4020.46 4020.41
4020.38 4020.46 4020.40
ENGLISH
14
Do not use equipment if you are not prepared
for its use. Before each use, inspect the
equipment as explained in this manual to
insure that equipment is in perfect state.
Do not make any modifications to equipment
other than mentioned in this manual. Do not
use replacement part other than mentioned in
this manual.
3. USE LIMITATIONS
Do not work under possible sever impact conditions. This
equipment is designed to protect under normal solder
conditions. This equipment does not protect against sever
impacts such as fragments from abrasive disks. Do not
use to protect from the use of abrasive disks.
Do not work out of the margins of this equipments design.
This equipment does not protect against corrosive liquids
or in an explosive atmosphere
Do not work out of the margins of this equipments design.
Using this equipment with temperatures lower than -5ºC
or higher than 55ºC effects filter design and could cause
permanent damage to the eyes and even loss of vision.
This equipment is not designed to work in wet conditions
or in water. Do not submerge in liquid.
Do not work out of the margins of this equipments design.
The use of this equipment in any other type of activity that
requires a level of protection higher than 13 could cause
permanent damage to the eyes and even a loss of vision.
This equipment is not designed to be used with laser
cutting or any other work that requires a grade greater
than 13.
Do not use this equipment in extensive overhead soldering.
Bad burns could be received if there is a possibility of
droppings from molten metal.
Do not use dissolvents on the filter or helmet.
4. CHARACTERISTICS
The products "solder mask AS-1.B" include 2 photo sensor
filters implanted at eye level. This filter darkens or lightens
automatically depending on the level of light induced.
The filter is transparent before soldering that the way
that the user can observe clearly the surface of the work
area. When the solder arc energizes, the filter will darken
3.
immediately. When the arc is finished, the filter will become
transparent once again.
The time that is takes for the filter to go from transparent
to dark is 0.0001 seconds.
The filter gives the user complete and permanent protection
from inferred and ultraviolet radiation even in transparent
mode. The level of protection against radiations IR/UV is
permanently set at 13 degrees.
14