GRAPHITE 58G000 Manual De Usuario página 10

safety devices which, if damaged, can cause the battery to
catch f i r e or explode.
Explanation of the used pictograms
1.Read the operating instructions, observe the warnings and safety
conditions contained therein.
2.Wear safety goggles and ear protection.
3.Keep children away from the appliance.
4.Protect from rain.
5.Use indoors, protected from water and moisture.
6.Recycling.
7.Second class of protection.
8.Selective collection.
9.Do not throw the cells into the fire.
10.Hazardous to the aquatic environment.
11.Do not allow heat to exceed 50°C.
INSTALLATION/SETTING
PREPARATION FOR WORK
REMOVING / INSERTING THE BATTERY
• Set the direction of rotation switch (5) to the centre position.
• Press the battery retaining button (8) and slide the battery out
• (7) (Figure A).
• Insert the charged battery (7) into the handle holder until the battery
retaining button (8) audibly engages.
CHARGING THE BATTERY
The device is supplied with a partially charged battery. The battery
should be charged in conditions where the ambient temperature is
40C - 400C . A new battery or one that has not been used for a long
period of time will reach full power capability after approximately 3 -
5 charge and discharge cycles.
• Remove the battery (7) from the unit (Fig. A).
• Plug the charger into a mains socket (230 V AC).
• Insert the battery pack (7) into the charger (12) (Fig. B).Check
that the battery pack is properly seated (pushed all the way in).
CAUTION
When the charger is plugged into a mains socket (230 V AC), the
green LED (11) on the charger lights up to indicate that the voltage is
connected.
When the battery pack (7) is placed in the charger (12), the red
LED (11) on the charger will illuminate to indicate that the battery is
being charged.
At the same time, the green LEDs (14) of the battery's state of charge
light up pulsatingly in different patterns (see description below).
• Pulse lighting of all LEDs - indicates battery depletion and the
need to recharge.
• Pulsating illumination of 2 LEDs - indicates partial discharge.
• Pulsating 1 LED - indicates high battery charge.
When the battery is charged, the LED (11) on the charger lights
up green and all the battery charge status LEDs (14) l i g h t
continuously. After a certain time (approx. 15s), the battery charge
status LEDs (14) go out.
The battery should not be charged for more than 8 hours.
Exceeding this time may damage the b a t t e r y cells. The
charger will not switch off automatically when the battery is
fully charged. The green LED on the charger will remain lit.
The battery charge status LED will turn off after a period of
time. Disconnect the power supply before removing the
battery from the charger socket. Avoid consecutive short
charges. Do not recharge the battery after using it for a
s h o r t t i m e .
necessary recharges indicates that the battery is worn out
and should be replaced.
Batteries become warm during the charging process. Do not
undertake work immediately after charging - wait until the
battery has reached room temperature. This will prevent
damage to the battery.
BATTERY CHARGE STATUS INDICATION
The battery is equipped with a b a t t e r y
indication (3 LEDs) (14). To check the charge status of the
b a t t e r y , press the b a t t e r y charge status indicator button
(13) (Fig. C). Lighting of all LEDs indicates a high level of battery
charge. The lighting of 2 diodes indicates partial discharge. The lighting
of only 1 diode indicates that the b a t t e r y is exhausted and needs
to be recharged.
CONSTRUCTION AND PURPOSE
The drill/driver is a battery -powered power tool. It is driven by a
permanent magnet DC commutator motor together with a planetary
gearbox. The drill/driver is designed for screwing and unscrewing
screws and bolts in wood, metal, plastics and ceramics and for
drilling holes in the aforementioned materials. Cordless, cordless power
tools are particularly useful for interior work, room adaptations, etc.
Do not m i s u s e the power tool.
DESCRIPTION OF THE GRAPHIC PAGES
The numbering below refers to the components of the unit shown
on the graphic pages of this manual.
1.Quick-action chuck
2.Quick-action chuck ring
3.Torque control ring
4.Gear shift switch
5.Direction of rotation switch
6.Handle
7.Battery
8.Battery attachment button
9.Switch
10.Lighting
11.LEDs
12.Charger
13.Battery charge status indicator button
14.Battery charge status indication (LEDs).
* There may be differences between the drawing and the product.
SPINDLE BRAKE
The drill/driver has an electronic brake that stops the spindle as
soon as pressure is released on the switch button
(9). The brake ensures precision in screwdriving and drilling by not
allowing the spindle to rotate freely when switched off.
OPERATION / SETTINGS
ON/OFF
Switching on - press the switch button (9).
Switching off - release pressure on the switch button (9).
Each time the on/off button (9) is pressed, the light is illuminated
a (LED) light (10) illuminates the work area.
SPEED CONTROL
The screwdriving or drilling speed can be adjusted during operation
by increasing or decreasing the pressure on the switch button (9).
Adjusting the speed allows a slow start, which, when drilling holes in
u p
plaster or tiling, prevents the drill bit from slipping, while when
screwing and unscrewing, helps to maintain control of the work.
OVERLOAD CLUTCH
Setting the torque adjustment ring (3) to the selected position
permanently sets the clutch to the specified torque amount. When
the set torque amount is reached, the overload clu t c h
automatically disengaged. This prevents the screw from being driven
10
A significant drop in the time between
charge status
is