Publicidad
Idiomas disponibles
Idiomas disponibles
ATTENTION
Ensure that the cable is not squeezed during assembly.
8.1
Installation of the lower push bar
(3) (Fig. 3)
1. Fit the two lower push bars (3) in the holes (3b) pro-
vided.
2. Fasten each of these with a Phillips screw (3a).
8.2
Installation of the upper push bar
(1) (Fig. 1, 4)
1. Screw the upper push bar (1) to the lower push bars
(3) with one flat head screw (2a) and a locking nut (2)
on each side.
8.3
Fitting the cable holder (8) (Fig. 1,
5)
1. Clip the two cable holders (8) into the upper push bar
(1) and lower push bar (3) and secure the cable (9).
8.4
Grass collection basket
8.4.1
Fit the carry handle (5a) to the grass
collection basket (5) (Fig. 1, 6)
Note:
The carry handle must be fitted on the upper side, where
the fill level indicator is also located.
1. Attach the carrying handle (5a) of the grass collection
bag (5) to the holder provided on the top of the grass
collection bag (5).
2. Screw the carry handle (5a) firmly to the inside of the
grass collection basket (5) with two screws (5b).
8.4.2
Mount the grass collection basket (5)
(Fig. 6)
WARNING
Danger of crushing!
Pay attention to your fingers!
• Wear gloves.
1. Clip both parts of the grass collection bag (5) together.
9
Pre-commissioning
NOTE
Some noise pollution from this product is un-
avoidable. Postpone noisy work to approved
and designated times. If necessary, adhere to
rest periods and limit the duration of work to
the bare minimum.
For your personal protection and the protec-
tion of nearby persons, wear suitable hearing
protection.
9.1
Setting the cutting height
ATTENTION
The cutting height may only be adjusted
when the engine is shut off.
WARNING
Danger of injury!
To switch off the product, switch off the motor, wait for it
to stop, remove the battery and pull out the safety key.
• In dense, tall grass, set the highest cutting level and
mow more slowly. A high cutting height should be se-
lected for the first cut of the season. Adjust the cutting
height so that the product is not overloaded.
• Set the cutting height depending on the actual length
of the lawn.
• Carry out several passes so that a maximum of 4 cm
of lawn is removed at a time.
The cutting height is adjusted via the front and rear axles.
WARNING
Danger of crushing!
Pay attention to your fingers!
3 different cutting heights can be set:
1 =
2 =
3 =
1. Lay the lawnmower on its side.
2. Start by gripping the sides of the rear wheel axle with
both hands.
3. Then pull evenly on the wheel axle and allow it to
latch into the desired position.
4. Repeat the process on the front wheel axle.
Note:
Set the wheel axles to the same cutting height.
9.2
Inserting/removing the battery (12)
in the battery mount (Fig. 1, 7)
Inserting the battery
1. Open the cover (6).
2. Push the battery (12) into the battery mount (13). The
battery (12) clicks into place audibly.
3. Close the cover (6).
Removing the battery
1. Open the cover (6).
2. Press the unlock button (14) of the battery (12) and
remove it from the battery mount (13).
3. Close the cover (6).
9.3
Preparing the area to be mowed
1. Before mowing, carefully examine the area.
2. Remove stones, sticks, bones, wires, toys and other
objects that may be ejected by the product.
www.scheppach.com
20 mm
45 mm
60 mm
GB | 25
Publicidad
