SYNQ DFX-48 Manual De Instrucciones página 4

ENGLISH
CONNECTIONS
Connections can be made with balanced/unbalanced jack or XLR-cables. Please only use good quality
cables to minimize noise and interference. The DFX-48 can be connected in two ways:
- Between a line level audio source and the input of your mixer.
- To the channel effect sends or AUX of a PA-mixer (effect send switched in post fader mode)
VIA PA-MIXER EFFECT SEND / AUX
(set the direct signal level to 0%)
Connector wiring:
FUNCTIONS (FRONT)
1. SIGNAL METER: indicates the level of the input signal, please check n°14 to see how you can adapt the
input sensitivity.
SYNQ
®
OPERATION MANUAL
BETWEEN AUDIO SOURCE AND MIXER INPUT
(set the direct signal level to your own taste)
3/46
ENGLISH
2. MULTIFUNCTIONAL DISPLAY: Indicates the status of the several function settings.
A Shows program number + name
B Shows the different effect parameters
C Flashes when you can save the new settings
3. EDIT WHEEL: used to browse the different effect programs. To select an effect you must confirm your
choice by pressing the ENTER button (9) within 5seconds. The edit wheel is also used to adjust the
different effect parameters.
4. PROGRAM BUTTON: used to select the different effects. Press this button to shift between the user
editable programs (display shows U01 to U48) and factory preset effects (display shows P01 to P48).
5. LOCK BUTTON: press this button for some seconds to lock all buttons (on the right of display line1 a
"key symbol" appears). Press this button again for some seconds to unlock all buttons ("key symbol"
disappears)
6. BYPASS BUTTON: press this button for some seconds to bypass the effect signal, only the original
(direct) signal will pass.
7. PARAMETER BUTTON: each effect uses different parameters, with the parameter button you can
browse these parameters. When a parameter is followed by a flashing ":", it can be changed with the
EDIT WHEEL (3). When "SV" appears on the display, you can use the ENTER button (9) to save the
new settings  see point 9 for more information.
8. EQ/RESET BUTTON: This button has two functions:
 EFFECT EQ: the sound of each effect can be modified using a 5band equalizer. The equalizer has
5 fixed frequencies (62Hz, 250Hz, 1kHz, 2kHz, 8kHz) that all can be adjusted from -12dB to +12dB
in 1dB-steps. When "SV" appears on the display, you can use the ENTER button (9) to save the
new equalizer settings, together with the other effect parameters  see point 9 for more
information.
 RESET USER PROGRAMS: to reset all user programs to the original factory settings, press the
RESET button until the display shows "PRESS [ENTER] TO RESET DATA". Press the ENTER
button (9) to confirm. Attention! ALL your personal settings will be lost!!!
9. ENTER BUTTON: used for several functions:
 Confirm effect of choice: to confirm your choice while browsing the different effect programs.
 Save modified parameters: when you change the parameters of an effect, "SV" starts flashing in
the lower right corner of the display to indicate that you can save the adapted settings. You should
follow these steps:
 Batch setup of direct signal: when the effect unit is used with the effect send/return of a PA-
mixer, you only want to send the effect signal back to the mixer and not the original (direct) signal.
This means that the direct signal in the output of the DFX-48 should be off (or 0 %). Follow these
steps to do this for all user programs at once:
10. ON/OFF SWITCH: used to switch the unit on/off
DFX-48 SYNQ
®
A Shows one of the 5 frequencies of the equalizer
B Shows the gain of the equalizer (+/-12dB)
C Flashes when you can save the new settings
a. Press the ENTER button (9): On the display one of the user programs (U01 - U48) starts
flashing.
b. Use the EDIT WHEEL (3) to select the user program (U01 – U48) you want to store your
settings to.
c. Press the ENTER button (9) again to confirm: the display shows "STORING DATA"
d. Done: new settings are stored.
a. Press the ENTER button (9) until the display shows "BATCH SETTING DIRECT: xx%"
b. Use the EDIT WHEEL (3) to set the level of the original (direct) signal. (for example: 0%)
c. Press the ENTER button (9) again until the display shows "SETTING BATCH DIRECT, PLS
WAIT"
d. Done: new level for the original (direct) signal is stored.
4/46
OPERATION MANUAL
DFX-48