Publicidad
SYMBOLS
To reduce the risk of injury, user must read
instruction manual
Wear eye protection
Wear ear protection
Wear dust mask
Warning
Double insulation
Waste electrical products must not be disposed
of with household waste. Please recycle where
facilities exist. Check with your local authorities
or retailer for recycling advice.
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction book
carefully.
INTENDED USE
The machine is intended for dry sanding of wood, plastic, filler and
coated surfaces.
1.FITTING THE SANDING PAPER (SEE FIG. A)
Fit the paper over the pad so that it covers the entire area. Make
sure the sanding paper is even with the edges and that the dust
collection holes in the pad and sanding paper is aligned and the
sanding paper evenly overlaps the pad. Never use your sander
without a sanding paper.
2. USING THE DUST COLLECTION BOX (SEE FIG. B)
Your sander is equipped with a dust collection box, which is
designed for collect dust task. Insert the dust collection box into
the rear dust outlet of sander. Then pull the dust collection box and
make sure it is tightened securely on the dust outlet.
3. USING THE DUST OUELET (SEE FIG. C)
Your sander is equipped with a 35mm dust outlet, which are
designed for connecting the hose of a vacuum cleaner.
If the vacuum hose is 35mm, insert the hose directly into the rear
dust outlet of sander.
First please turn on the vacuum cleaner, and then turn on the
sander. If you stop sanding, first turn off the sander, and then turn
off your vacuum cleaner.
NOTE: Please pull the dust adapter to make sure tightened securely
on the dust outlet.
4. OPERATING THE SWITCH (SEE FIG. D)
To operate the sander, plug into mains (make sure switch is in
switch off position first). Grip sander firmly and switch on.
Depress the switch (2) to start or stop your palm sander.
8
5. USING THE SANDER
Your sander is equipped with a teardrop base which allows you to
use it on large flat surfaces, as well as difficult and confined areas.
The workpiece to be sanded must be secured. If it is small or it
may move during sanding, it must be held in a vice or suitably
clamped.
Be sure to hold the sander firmly while it is on and apply it gently
to the work, it may "kick" on first contact. Hold the sander so that
it is flat on the work and move slowly, preferably with a smooth,
circular motion. Regularly check the condition of the sanding paper
and replace when worn for best results.
6. ORBITAL SANDING
Your sander operates in small circular rotations which allows
efficient material removal.
Operate your sander in long sweeping movements across your
workpiece and even across the grain. For a finer finish, always use
a fine grain sandpaper and only move the sander in the direction of
the grain and never across the grain.
Do not allow your sander to remain in the same position otherwise
you will remove material and create and uneven surface.
WORKING HINTS FOR YOUR SANDER
If your power tool becomes too hot, especially when used at low
speed, set the speed to maximum and run with no load for 2-3
minutes to cool the motor. Avoid prolonged usage at very low
speed. Always use a sanding belt suited to the material you wish
to sand. Always ensure the work-piece is firmly held or clamped
to prevent movement. Support large panels close to the sanding
area. Any movement of the material may affect the quality of the
sanding finish. Start your sander before sanding and turn off only
after stopping sanding. For best results, sand wood in the direction
of the grain. Do not start sanding without the sanding belt fitted.
Empty the dust bag every 5 minutes or sooner to ensure efficient
dust collection.
MAINTENANCE
Remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
Your power tool requires no additional lubrication or maintenance.
There are no user serviceable parts in your power tool. Never use
water or chemical cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool in a dry place. Keep
the motor ventilation slots clean. Keep all working controls free
of dust.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
TROUBLESHOOTING
1. If your sander will not operate, check the power at the mains
plug.
2. If the sander does not abrade surface, checking the sanding
paper. If the sanding paper has been worn, replace the new
paper and try again. The paper must be kept in a dry place, if
it is allowed to become damp, the abrasive particles will lose
their adhesion to the backing paper and will not abrade.
3. If the sander dose not move smoothly, The sanding paper
may be loose, damaged or wrinkled. Replace and try again.
4. If a fault can not be rectified return the sander to an
authorized dealer for repair.
EN
Publicidad
