Publicidad
Idiomas disponibles
Idiomas disponibles
ATTENTION
A damaged dust cap must be replaced immediately.
It is recommended to have this done by a service
centre.
1. Pull the locking sleeve (3) backwards to unlock the
SDS-Plus tool receiver (1).
2. Insert the tool attachment (15/ 16/ 17/ 18/ 19) into
the SDS-Plus tool receiver (1) by turning it.
3. Release the locking sleeve (3).
4. Check that the tool attachment (15/ 16/ 17/ 18/ 19)
is firmly seated by pulling on it.
The tool attachment (15/ 16/ 17/ 18/ 19) has some
radial play due to the system.
8.3
Removing the tool attachment
(15/ 16/ 17/ 18/ 19) (Fig. 1, 3)
1. Pull the locking sleeve (3) backwards and remove
the tool attachment (15/ 16/ 17/ 18/ 19).
8.4
Fitting the depth stop (4) (Fig. 1)
1. Slide the depth stop (4) into the small opening on
the additional handle (13). The teeth on the depth
stop (4) should point downwards.
2. Position the depth stop (4) so that the distance be-
tween the tip of the tool attachment (15/ 16/ 17/ 18/
19) and the tip of the depth stop (4) corresponds to
the desired drilling depth.
3. Tighten the depth stop locking screw (5) to deter-
mine the depth stop (4).
9
Operation
WARNING
Danger of injury!
Remove the battery from the power tool before carry-
ing out any work on the power tool (e.g. maintenance,
tool change, etc.) and when transporting and storing
it. There is a risk of injury if the on/off switch is oper-
ated unintentionally.
ATTENTION
Make sure that the ambient temperature does not ex-
ceed 50°C and does not fall below -20°C during work.
ATTENTION
The product is part of the 20V gomag series and may
only be operated with batteries of this series. Batter-
ies may only be charged with battery chargers of this
series. Observe the manufacturer's instructions.
9.1
Selecting operating mode (Fig. 1)
ATTENTION
The operating mode may only be changed at a stand-
still.
1. Use the operating mode selector switch (6) to
choose the operating mode of the product.
2. Turn the mode selector switch (6) to the desired po-
sition.
When the desired position is reached, the mode se-
lector switch (6) audibly engages.
Function
Drilling (striking
mechanism OFF)
Percussion drilling
(striking mechanism ON)
Chisel position adjustment
Chisel
9.1.1
Note:
* = not included in the scope of delivery!
1. Set the mode selector switch (6) to the symbol
2. Turn the tool attachment* in the SDS-Plus tool re-
ceiver (1) to the required position.
3. Select the symbol for the chisel operation with the
mode selector switch (6)
9.2
Adjusting the direction of
rotation (Fig. 1)
ATTENTION
The direction of rotation switch may only be actuated
when idle.
With the direction of rotation switch, you can select the
direction of rotation of the product (clockwise or anti-
clockwise) and secure the product from being switched
on unintentionally. The arrow on the direction of rotation
switch indicates the working direction.
1. Wait until the product has come to a standstill.
2. Push the direction of rotation switch (7) to the de-
sired position:
– Clockwise rotation: Press the direction of rota-
tion switch to the right.
– Anti-clockwise rotation: Press the direction of
rotation switch to the left.
3. Switch lock: Put the direction of rotation switch in
the centre position.
9.3
On/Off switch (8) (Fig. 1)
1. To switch on the product, push the on/off switch (8).
www.scheppach.com
Operating mode:
Drill setting
Hammer-drill setting
Level
Chisel level
Adjust chisel position
.
.
GB | 25
Publicidad
