Publicidad
Idiomas disponibles
Idiomas disponibles
Variant 2
1. Press the on/off switch (11). The display (4) switch-
es on. The product starts.
2. To restart the product, press the on/off switch (11)
twice.
9.3.2
Switching off the product
1. Press the on/off switch (11) once.
2. Press and hold the on/off button (6) for 3 seconds.
The display (4) goes off.
Note:
The preset pressure is saved.
Note:
If your product does not start when you press the on/off
switch (11), proceed as described underSwitching on
the product.
9.3.3
LED work lamp (10)
This product is equipped with an LED work lamp to illu-
minate the immediate work area and improve visibility
in poorly lit environments.
CAUTION
Do not look directly into the LED work lamp or the
light source.
1. The LED work lamp (10) lights up automatically as
soon as the product is switched on.
9.4
Inflating
Note:
Do not overinflate inflatables! They could burst. Deter-
mine the maximum pressure before inflating.
1. Remove the valve cap of the inflatable.
2. If necessary, fit the compressed air hose (12).
3. If necessary, open the fixing lever (12b).
4. Plug
the
desired
(13/14/15/16) onto the valve connection (12a) of the
compressed air hose (12).
5. Push the fixing lever (12b) closed again (in the di-
rection of the compressed air hose).
6. Set the desired pressure on the display (4) as de-
scribed in Setting the pressure.
7. Insert the ball needle/valve adapter (13/14/15/16)
into the valve of the inflatable.
8. Switch the product on.
9. Press the on/off switch (11). The LED work lamp
(10) lights up. When the preset pressure is reached,
the product switches off automatically.
10. Attention! The adapters can get hot! Remove the
ball needle/valve adapter (13/14/15/16).
11. Fit the valve cap again.
valve
adapter/ball
needle
www.scheppach.com
10 Working instructions
Note:
By briefly pressing the on/off button on the display, you
can switch the pressure unit display between "bar" and
"psi" (pounds per square inch).
10.1
Setting the pressure
1. Switch on the display (4) on the battery hand com-
pressor as described under Switching on/off.
2. Press the "+" button (5) on the display (4) to in-
crease the pressure setting. To do this, press and
hold the "+" button (5) for approx. 3 seconds. The
digits in the display (4) start flashing. You can now
increase the preset value by pressing the "+" button
(5). Here, the numerical value is changed by 0.1
bar /1 PSI each time it is pressed.
3. To decrease the preset value, proceed accordingly
with the "-" key (7).
11 Cleaning and maintenance
WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
There is a risk of accident! Always perform
maintenance and cleaning work with the
battery removed. There is a danger of inju-
ry! Let the Product cool down before all
maintenance and cleaning tasks. Elements
of the engine are hot. There is a danger of
injury and burning!
The product can start unexpectedly and cause inju-
ries.
–
Remove the battery.
–
Allow the product to cool down.
–
Remove the tool attachment.
11.1
Cleaning
1. Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub the
product clean with a clean cloth or blow it off with
compressed air at low pressure. We recommend
that you clean the product directly after every use.
2. Ventilation openings must always be free.
3. Do not use any cleaning products or solvents; they
could attack the plastic parts of the product. Make
sure that no water can penetrate the product interi-
or.
GB | 23
Publicidad
