Craftsman CMCD700 Manual De Instrucciones página 6

English
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
or AC ........... alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories, when replacing line, or
prior to cleaning. An accidental start‑up can cause injury.
Installing a Bit or Accessory into a Keyless Chuck
(Fig. D)

WARNING: Do not attempt to tighten drill bits (or any
other accessory) by gripping the front part of the chuck and
turning the tool on. Damage to the chuck and personal injury
may result. Always lock off trigger switch and disconnect tool
from power source when changing acces sories.

WARNING: Always ensure the bit is secure before starting
the tool. A loose bit may eject from tool causing possible
personal injury.
To insert a drill bit or other accessory, follow these steps.
1. Turn tool off and remove battery pack.
2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
3. Insert the accessory about 3/4" (19 mm) into the
chuck 7 and tighten securely by grasping and rotating the
chuck sleeve 11 clockwise with one hand while holding
the tool with the other. When the chuck is nearly tightened
you will hear a clicking sound. After 7 clicks the chuck
is securely tightened around the accessory. Your tool is
equipped with an automatic spindle lock mechanism. This
allows you to open and close the chuck with one hand.
Be sure to tighten chuck with one hand on the chuck sleeve
and one hand holding the tool for maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
Speed Selection (Fig. A)
The tool features two speed settings for greater versatility.
nOTE: Do not change speeds when the tool is running.
Always allow the tool to come to a complete stop before
changing speed.
6
n o ....................... no load speed
n ......................... rated speed
PSI....................... pounds per square
inch
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation–
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
..................... do not expose to
rain
1. To select speed 1 (higher torque setting), slide the speed
selector back (away from the chuck).
6
2. To select speed 2 (lower torque setting), slide the speed
selector forward (towards the chuck).
If the tool does not change speeds, confirm that the speed
selection switch is completely engaged in the forward or
back position.
Mode Selection (Fig. A)
The mode selection collar
the correct operating mode depending upon the
planned application.
To select, rotate the collar until the desired symbol aligns
with the arrow.

WARNING: When the mode selection collar is in the
drill, the drill will not clutch. The drill may stall if overloaded,
causing a sudden twist.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories, when replacing line, or
prior to cleaning. An accidental start‑up can cause injury.
Installing and Removing the Battery Pack (Fig. B)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button and firmly pull the battery pack out of the tool
2
handle. Insert it into the charger.
Proper Hand Position (Fig. C)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main
handle 9 and the other hand holding the battery pack
Variable Speed Trigger and Forward/Reverse
Control Button (Fig. A)
The tool is turned on and off by pulling and releasing
the variable speed trigger
depressed, the higher the speed of the tool. Your tool is
equipped with a brake. The chuck will stop as soon as the
trigger switch is fully released.
A forward/reverse control button
rotational direction of the tool and also serves as a
lock‑off button.
• To select forward rotation (clockwise), release the trigger
and depress the forward/reverse control button on the right
side of the tool.
• To select reverse (counterclockwise), depress the forward/
reverse control button on the left side of the tool.
nOTE: The center position of the control button locks the
tool in the off position. When changing the position of the
control button, be sure the trigger is released.
can be used to select
5
1 into the tool handle, align the
. The farther the trigger is
3
determines the
4
1 .