Publicidad
Idiomas disponibles
Idiomas disponibles
Skimmer Infinity
Installation in a pool frame made from masonry, insulating blocks, concrete, etc.,
lined with pool liner
1
2
3
16
Figure 4.
B
14
15
16
18
Figure 6.
Install as follows:
-A ( 1 : 3 )
NOTE! When pouring concrete/reinforcing the frame, the rebar must not be
any closer to stainless steel material than 50 mm.
1. Make a hole for the skimmer in the frame, dimensions and location as shown in Fig. 3, 4,
5, 6 and 7.
Install and secure the skimmer in the frame (see figures above).
The water surface must be 30 – 40 mm below the top edge of the skimmer.
2. The skimmer's flange must be level with the finished pool wall.
3. Install level monitor according to instruction MA55-49.
4. The product is provided with an equipotential bonding point (25). See IEC 60364-7-702
and current national building regulations with respect to equipotential bonding.
Please note that improper equipotential bonding can cause galvanic corrosion.
5. Connect pipe coupling to the pool circulation using a suitable thread sealant.
6. The drainage pipe (14) is glued to the pipe muff (15) using a suitable PVC adhesive and
fitted in the skimmer with the enclosed gasket and nipple (16). Connect pipe fittings to
the overflow.
7. Mask the skimmer's exposed flange and openings before pouring concrete, to prevent
concrete splashes.
8. Attach the self-adhesive gasket (6) to the skimmer (after pouring).
9. Install the flap gate (17) and check that it is correctly located and can move.
10. Place the liner in the pool.
11. Fill the pool with enough water for the water surface to reach 5 cm below the skimmer. Turn off the water.
12. Fit the outer gasket (9) and the mounting frame (10) - fasten first, then tighten crosswise.
13. Carefully cut the liner cleanly along the inside of the mounting frame (10). Now, continue to fill the pool with water, until the
water surface reaches the centre of the skimmer's opening.
14. Fit the front frame (12).
15. Install/adjust the collar:
If necessary, cut the plastic collar (2) to height, so it matches the surface coating surrounding the pool. Apply a suitable sealing
compound to the underside of the collar against the skimmer. Press the collar down against the skimmer. Secure the collar in
place with the enclosed screws (3).
16. Press the cover (1) into the collar.
4
6
9
21
20
17
19
B
21
22
20
A-A ( 1 : 3 )
Unless otherwise stated:
The 3D-model is correct and made in
the middle of the tolerance zon.
Tolerances/dimensions in this
document take priority over values
All dimensions are after
found in 3D-model.
surface treatment.
Designed by
Date of issue
Unit
Paul.Drotz
2021-11-01
mm
3
1
10
12
13
11
16
25
22
7
Figure 5.
8
10
8
13
14
12
15
Unless otherwise stated:
General surface profile tolerance
Threads
The 3D-model is correct and made in
ISO 965
8
the middle of the tolerance zon.
Tolerances/dimensions in this
document take priority over values
All dimensions are after
found in 3D-model.
surface treatment.
16
Designed by
Date of issue
Unit
E
3D-model
Tolerancing
Paul.Drotz
2021-11-01
mm
M20650-0
ISO 8015
7
Isolerblock med liner
B
18
B
Figure 7.
A-A ( 1 : 3 )
General surface profile tolerance
Threads
Edges of undefined
Unless otherwise stated:
The 3D-model is correct and made in
ISO 965
shape ISO 13715
the middle of the tolerance zon.
Tolerances/dimensions in this
document take priority over values
All dimensions are after
found in 3D-model.
surface treatment.
Designed by
Date of issue
Unit
E
3D-model
E
3D-model
Tolerancing
Art.no.
Paul.Drotz
2021-11-01
mm
M20650-0
M20650-0
ISO 8015
Isolerblock med liner
Isolerblock med liner
Drawing number
M20650 0
11
4
2
19
17
C
Edges of undefined
Surface roughness
shape ISO 13715
(Ra) ISO 1302
Art.no.
Side
of
2
(2)
Sheet size
A2
Drawing number
Revision
M20650 0
-
1. Lid
(incl. silicone sleeves)
2. Collar
A-A ( 1 : 3 )
3. Screw
4. Edge frame
5. -
6. Self-adhesive gasket 1.5 mm
Surface roughness
General surface profile tolerance
Threads
Edges of undefined
Surface roughness
(Ra) ISO 1302
ISO 965
shape ISO 13715
(Ra) ISO 1302
7. Wall mat
Tolerancing
Art.no.
Side
of
Side
of
1
8. Liner
(2)
ISO 8015
1
(2)
Sheet size
Sheet size
A2
A2
Drawing number
Revision
9. Gasket 2 mm
M20650 0
-
Revision
-
10. Mounting frame
11. Screw M5x16 (13x)
12. Front
13. Countersunk screw M5x25 (6x)
14. PVC drainage pipe
15. Pipe muff
16. Nipple and gasket
17. Flap gate
18. Screen basket
19. Skimvac plate
20. Rebar
21. Insulating block
22. Concrete
23. Masonry (LECA block)
24. Plaster
25. Equipotential bonding point
ENGLISH
6
9
10
12
11
13
25
8
7
24
23
10
11
12
8
Unless otherwise stated:
C
Tolerances/dimensions in this
document take priority over values
7
found in 3D-model.
Designed by
Date of issue
Paul.Drotz
2021-11-01
24
C
23
Unless otherwise stated:
Tolerances/dimensions in this
document take priority over values
found in 3D-model.
Unless otherwise stated:
General surface profile tolerance
Threads
The 3D-model is correct and made in
Designed by
ISO 965
the middle of the tolerance zon.
Paul.Drotz
Tolerances/dimensions in this
All dimensions are after
document take priority over values
found in 3D-model.
surface treatment.
Designed by
Date of issue
Unit
E
3D-model
Tolerancing
Paul.Drotz
2021-11-01
mm
M20649-0
ISO 8015
Mursten med liner
The 3D-model is correct and
the middle of the tolerance zo
All dimensions are after
surface treatment.
Unit
E
3D-mod
mm
M2064
Mu
The 3D
the mid
All dim
surface
Edges of undefin
Date of issue
Unit
shape ISO 13715
2021-11-01
mm
Art.no.
Drawing nu
M
Publicidad
