EdilKamin ELLKAMIN 8 Instalación Uso Y Mantenimiento página 53

Changing pellet loading
Press the "M" button for two seconds from the radio control
and scroll the display instructions with the "+" and "-" buttons.
You will come across the message "User menu" and when you
confi rm, the message "ADJ-PELLET and ADJ-DRAUGHT"
will appear.
If we set "Auto-adjust. ON", the system will automatically
adjust pellet dropping. Alternatively, if we set "Auto-adjust.
OFF," we can manually correct pellet dropping, varying the
range in terms of percentages (+/- 30 %).
By confi rming this function with the menu key, you can access
the function to adjust pellet loading. By decreasing the
value set, pellet loading is decreased. By increasing the value
set, pellet loading increases. This function is useful if
changing the pellet type for which the insert has been calibra-
ted and loading therefore needs correcting.
Should this correction not suffi ce, contact the Edilkamin-autho-
rised Dealer, to establish the new operating axis.
Notes on fl ame variability
Flame status may vary depending on the type of pellet used,
in addition to normal solid fuel fl ame variability and regular
combustion chamber cleaning carried out automatically by the
boiler.
(N.B.: which does NOT replace necessary cold suction by the
user prior to ignition).
RESERVE WARNING
The PELLKAMIN is fi tted with an electronic function that
detects the residual quantity of pellets in the tank.
The detection system is integrated into the electronic board,
allowing you to see how many hours and kg are left until
pellet exhaustion, at all times. For correct system function, it is
important that the following procedure is followed during the
fi rst ignition (by the Dealer).
Pellet reserve system
Before enabling the system, you need to load a sack of pellets
into the tank and use the PELLKAMIN until the loaded
fuel has run out. This allows for a short system road test.
After this, the tank can be fi lled completely and the PELLKA-
MIN started up.
When running, at the time at which a whole 15 kg sack of pel-
lets can be loaded, the display will show the word
"Reserve" fl ashing.
At this point, after having poured in a sack of pellets, you need
to 'inform' the memory that you have loaded 15 kg.
To do so, proceed as follows:
1. press the "M" key (for approximately 3-4 seconds) until the
word "Clock" appears.
2. press the "+" key until the word "Reserve" appears.
3. press the "M" key until the following screen appears,
INSTRUCTIONS FOR USE
- 53
Kg remaining in tank
then use the "+" key to take the fi gure (*) to the value equal to
the Kg of pellets loaded (15 kg in the above example).
4. press the "M" key to confi rm
5. press the key
After having completed the above procedure, after having con-
sumed the 15 kg, the wording "Reserve" will appear
fl ashing at intervals. After which the operation must be repea-
ted, from point 1 to point 5.
SIMPLIFIED LIGHTING BUTTON
If the radio remote control device does not work, you can carry
out the basic functions by means of a 1,20-metre cable, com-
plete with simplifi ed on-button, to be placed near the insert by
the installer (see Fig. 28).
Press the button once or multiple times to activate the desired
function:
1. A PELLKAMIN OFF
by pressing the red button for 2 seconds this turns on.
2. A PELLKAMIN ON
by pressing the red button for 2 seconds this turns off.
3. A PELLKAMIN ON
manual mode, by pressing the red button, you go from P1 to
P3.
4. A PELLKAMIN ON
automatic mode, by pressing the red button, you go from 5°C
to 30°C.
fi g. 28
The simplifi ed ON-button may be positioned near to the insert,
taking care to choose an installation point where temperatures
do not rise above 60°C.
Alternatively, it can be positioned inside the electricity box
supplied.
The button supplied can be substituted with another normally
open (NO) button, of any type or brand.
The button is wired separately from the power cables (230
VAC) with a maximum length of 2.0 m. For longer distances,
use a decoupling relay.
-
Kg loaded
to exit.
simplifi ed lighting
button