Wesco WS3173 Manual De Instrucciones página 7

2. DRILLING STEEL
Select the drill/impact action selector switch to the "
HSS drill bits should always be used for drilling steel with a lower
speed.
3. PILOT HOLES
When drilling a large hole in tough material (i.e. steel), we
recommend drilling a small pilot hole first before using a large drill
bit.
4. DRILLING TILES
Select the drill/impact action selector switch to the "
drill the tile. When tile has been penetrated, switch over to "
position.
5. COOL THE MOTOR
If your power tool becomes too hot, set the speed to maximum and
run no load for 2-3 minutes to cool the motor.
MAINTAINACE
Remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
There are no user serviceable parts in your power tool.
Never use water or chemical cleaners to clean your power tool. Wipe
clean with a dry cloth. Always store your power tool in a dry place.
Keep the motor ventilation slots clean.Keep all working controls free
of dust. Occasionally you may see sparks through the ventilation
slots. This is normal and will not damage your power tool.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
ENVIRONMENTAL PROTECTION
Waste electrical products must not be disposed of with
household waste. Please recycle where facilities exist.
Check with your local authorities or retailer for recycling
advice.
PLUG REPLACEMENT (ONLY FOR
REWIRABLE PLUG OF UK & IRELAND)
If you need to replace the fitted plug then follow the instructions
below.
IMPORTANT
The wires in the mains lead are colored in accordance with the
following code:
Blue = Neutral
Brown = Live
As the colors of the wires in the mains lead of this appliance
may not correspond with the colored markings identifying the
terminals in your plug, proceed as follows. The wire which is
colored blue must be connected to the terminal which is marked
with N. The wire which is colored brown must be connected to
the terminal which is marked with L.
Warning!
Never connect live or neutral wires to the earth terminal of the
plug. Only fit an approved 13ABS1363/A plug and the correct
rated fuse.
Note: If a moulded plug is fitted and has to be removed take
great care in disposing of the plug and severed cable, it must be
destroyed to prevent engaging into a socket.
EN
" position.
Connect
Blue to N
(neutral)
Outer sleeve
clamped
" position to
"
DECLARATION OF CONFORMITY
We,
POSITEC Germany GmbH
Postfach 32 02 16, 50796 Cologne, Germany
On behalf of Positec declare that the product
Description
Type designation WS3173 (31 - designation of machinery,
representative of impact drill)
Function
Complies with the following Directives,
2006/42/EC, 2014/30/EU, 2011/65/EU&(EU)2015/863
Standards conform to
EN 62841-1, EN 62841-2-1, EN 55014-1, EN 55014-2,
EN IEC 61000-3-2, EN 61000-3-3
The person authorized to compile the technical file,
Name
Address
Postfach 32 02 16, 50796 Cologne, Germany
2023/2/11
Allen Ding
Deputy Chief Engineer, Testing & Certification
Positec Technology (China) Co., Ltd
18, Dongwang Road, Suzhou Industrial
Park, Jiangsu 215123, P. R. China
DECLARATION OF CONFORMITY(UK)
We,
Positec Power Tools (Europe) Ltd,
PO Box 6242, Newbury, RG14 9LT, UK
On behalf of Positec declare that the product
Description
Type designation WS3173 (31 - designation of machinery,
representative of impact drill)
Function
Complies with the following regulations:
Cable grip
Impact drill
Boring holes in various materials
Marcel Filz
POSITEC Germany GmbH
Impact drill
Boring holes in various materials
Fuse
Brown L(live)
7