Cleaning And Maintenance - ExtraStove ES 9 Manual De Instalación

G
6.0 How to use the air ducting (where present)
The ductable stove is equipped with an independent SELECTORS adjustment system,
which is located under the door of the pellets tank in the upper part of the stove.
ATTENTION!
Selector must be used only when the stove is cold.
The SELECTORS adjustment system, allows the air distribution independently (right side and left
side), according to the needs, simply by moving the SELECTORS in positions A-B-C-D-E.
- Lifting and moving the knob in position "A" the air flow is conveyed 100% at the front of the stove.
- Lifting and moving the knob in position "B" (where installed), the airflow is conveyed 75% at the
front of the stove and 25% on the rear of the stove.
- Lifting and moving the knob in the position "C" the airflow is conveyed 50% at the front of the
stove and 50% at the rear of the stove.
- Lifting and moving the knob in the position "D" (where installed), the airflow is conveyed 25% at
the front of the stove and 75% at the rear of the stove.
- Lifting and moving the knob in position "E" the airflow is conveyed 90% at the rear of the stove.

7.0 Cleaning and maintenance

Before effecting any maintenance operation or cleaning on the stove, take the following
precautions:
• Be sure that all parts of the stove are cold.
• Be sure that the ashes are completely cold.
• Be sure that the general switch is in the "OFF" position.
• Be sure that the plug is pulled out of the socket to avoid accidental contact.
• Once the maintenance phase is completed check that everything is in order as per
before the intervention (the brazier is placed correctly).
Follow carefully the following cleaning instructions. Failure to follow
these instructions could create problems with the operation of the
stove.
7.1 How to clean the combustion chamber for models ES 9/10/12
(once a month)
When the stove is cold, please join the following procedure:
- operate 5-6 times the scrapers the heat exchange pipe pulling and pushing the two
levers located under the cover of the pellet tank.
Pellet tank
- Open the door and remove the brazier and the ash tray (Pict. 1).
- Unscrew the screws. Remove the outside fireproof bulkheads. Just move them out
without rotating. If required, use a screwdiver or a similar tool. (Pict. 2-3-4).
- Remove the central bulkhead of the combustion chamber. (Pict. 5).
- Dismantle the inside lateral bulkheads levering with a screwdiver on the point indicated
in the picture 5-6-7-8.
- Remove the bottom of the combustion chamber using a screwdiver and starting defi-
nitively from the right side.(Pict. 9-10-11).
Pict. 1
Scrapers
-
Pict. 2 Pict. 3
Use a vacuum cleaner to clean the inner part of the combustion chamber from the re-
sidual ash (Pict. 12).
- Reassemble everything in reverse order.
Pict. 4
Pict. 6
Pict. 9
7.2 How to clean the combustion chamber for the model ES 16/16 C
(once a month)
When the stove is cold, please join the following procedure:
- operate 5-6 times the scrapers the heat exchange pipe pulling and pushing the two
levers located under the cover of the Pellet tank.
Pellet tank
- Open the door and remove the brazier and the ash tray (Pict. 13-14).
- Remove the internal parts (left and right) and the central part pushing up and pulling
outward (pict. 15-16).
- Unscrew the two screws inside the door and remove the fire heater ( pict. 17-18)
- move and slide the scraper and clean the inside well with the vacuum cleaner (pict. 19)
- Reassemble everything in reverse order.
20
Pict. 5
Pict. 7 Pict. 8
Pict. 10 Pict. 11
Fig. 12
Scrapers