Cleaning The Surfaces; Cleaning The Glass - ExtraStove ES 9 Manual De Instalación

Fig. 13
Fig. 16

7.3 Cleaning the surfaces

To clean the surfaces, use a rag dampened with water or with water and a neutral de-
tergent.
The use of aggressive detergents or thinners can damage the sur-
faces of the stove. Before using any detergent it is advisable to try
it on a small section out of sight or contact the Authorized Assi-
stance Centre for information regarding the product.
7.4 Cleaning the metal parts
To clean the metal parts of the stove, use a soft cloth dampened with water.
Never clean the metal parts with alcohol, thinners, petrol, acetone or other degreasing
substances. If such substances are used, our company declines any responsibility.
Eventual variations in the colour of the metal parts can be caused by an incorrect use
of the stove.
WARNING! it is necessary to daily clean the brazier and clean the
ash box. Periodically remove and empty the cap of the inspection
"T" pipe located behind the stove (see picture 20 and 21). The lack
of cleanliness can prevent the starting of the stove, causing dama-
ges to the stove itself and to the environment (possible emission of
unbrunt material and soot). Do not re-use the pellet possibly remai-
ned in the brazier due to no starting-up.
Fig.20
7.5 Cleaning the brazier and brazier support
When the flame assumes a red colour or seems weak, and is accompanied by black
smoke, this means that there are ash deposits or incrustations that do not permit the
correct functioning of the stove and that must be removed (Pict. 22a-22b).
Remove the brazier every day by simply raising it from its slot; then clean out the ashes
and eventual incrustations that may have formed, paying particular attention to liberating
the holes by using a pointed tool (not included with the stove)
Fig. 14 Fig. 15
Fig. 17 Fig. 18
SCRAPERS
Fig. 19
Fig.21
This operation is made particularly necessary before every lighting the first several times
and above all if using pellets that differ from those supplied by our company. The fre-
quency of this operation is determined by how frequently the stove is used and the
choice of pellets. It is also a good idea to check the brazier support, vacuuming the even-
tual ash present.
Fig.22a
7.6 Daily cleaning with a scraper
When the stove is cold, please join the following procedure:
- operate 5-6 times the scrapers the heat exchange pipe pulling and pushing the two
levers located under the cover of the Pellet tank.
Pellet tank
7.5.1 Daily cleaning with a scrapers and door opening door for model ESP plus
To open the door, insert the provided special tool in the slot and pull upward (pict. 23a).
To clean the tubes, take out the scrapers from the slots in front of the pellet tank with
the provided special tool and push and pull them manually (pict. 23b).
Pict. 23a
7.7 Ash box
Open the door and extract the ash box (Pict. 24). Use a vacuum to remove all the ash
deposited within. This operation must be performed more or less frequently depending
on the quality of the pellets used.

7.8 Cleaning the glass

The glass is a self cleaning type, therefore, while the stove is working, a veil of air is
blown across its surface to remove ash and dirt; nevertheless over a period of several
hours, a greyish patina tends to form which should be cleaned when the stove is next
shut down. How dirty the glass becomes also depends on the quality and quantity of
pellets used. Cleaning the glass should be done when the stove is cold with products
recommended and tested by our company.
When performing this operation, always check that the grey seal around the glass is in
a good state; failure to check the efficiency of this gasket can compromise the function
of the stove. Poor quality pellets can, in any case, cause the glass to become dirty.
WARNING!
If the glass is broken, do not attempt to light the stove.
21
G
Fig.22b
Scrapers
Pict. 23b
Pict. 24