Publicidad
Mounting of PLUS FAN
Mounting of PLUS FAN
7. INSTALLATIE VAN VANVENT
DE
1.Open mounting holes for the PLUS FAN on the roof (strong wall with a width ≥30mm is
OPMERKING:
required around the hole to ensure that the self-tap screw can be firmly nailed into that
1.Open mounting holes for the PLUS FAN on the roof (strong wall with a width ≥30mm is
wall) according to the hole size drawing on the [Mounting Dimensions] page. Power cord
required around the hole to ensure that the self-tap screw can be firmly nailed into that
de VanVent te installeren als u niet over voldoende installatiekennis beschikt.
EN
wall) according to the hole size drawing on the [Mounting Dimensions] page. Power cord
≥50mm can be optionally reserved in the opening on the left or right side of the body.
≥50mm can be optionally reserved in the opening on the left or right side of the body.
IT
ES
R5
R5
FR
NL
The outlet on the left side of the vehicle body is taken as an example in this manual.
The outlet on the left side of the vehicle body is taken as an example in this manual.
FI
In deze handleiding wordt de uitlaat aan de linkerkant van
2.Take out the vehicle body fixing plate from the package, and inject sealant (MS type
2.Take out the vehicle body fixing plate from the package, and inject sealant (MS type
de carrosserie als voorbeeld genomen.
sealant recommended) into the rubber groove of the outer ring of the vehicle body
sealant recommended) into the rubber groove of the outer ring of the vehicle body
DK
fixing plate frame. The sealant should not be too much, and any excessive glue should
fixing plate frame. The sealant should not be too much, and any excessive glue should
be cleaned up with a soft scraper.
be cleaned up with a soft scraper.
SE
Mounting of PLUS FAN
De hoeveelheid kit moet gelijkmatig zijn. Breng niet te veel
The amount of glue should be even. Do not apply too much glue.
kit aan.
3.Fix the body fixing plate on the wall of the motor home with ST4.2×25 cross pan-head
The amount of glue should be even. Do not apply too much glue.
screws (16 pcs) outside the body. After fixing the screws, remove excessive glue around
the body fixing plate, if any.
The fixing screw must be fixed firmly.
De bevestigingsschroef moet stevig vastzitten.
4.Remove the upper part of the PLUS FAN top cover, align it with the body fixing plate
frame, and insert the upper part into the frame. After pressing, apply an appropriate
amount of sealant (recommended to use MS type sealant) to (PT4.0 × 12 (4)), and then
use screws to fix the upper part of the body fixing plate.
Wij raden installatie door gekwalificeerd personeel aan. Vraag uw dealer om
12 V
CARBEST VanVent | 318028/318029
1.
Controleer voor de installatie
de dakdikte, die tussen 27
mm en 80 mm moet liggen.
Markeer de uitsnijdopening
(400x400 mm) op het dak en
snijd het gat in het dak.
het 12 V netsnoer (>=50 mm)
van de accu van het voertuig
kan worden gereserveerd in
de opening aan de linker- of
rechterkant.
2.
Voordat de VanVent wordt
geïnstalleerd, moet het opper-
vlak worden gereinigd (vrij van
stof en vet). Breng voldoende
geschikte lijm aan (aanbevolen
DEKAseal 8936) rond de rand
van het montageframe.
13
3.
13
Bevestig het montageframe op
het dak van het voertuig met
kruiskopschroeven ST4.2x25
(16 stuks).
Verwijder overtollige lijm.
60
Publicidad
