Farfisa ALBA Serie Manual Del Usuario página 14

Factory settings.
The values of the main factory settings
are listed below.
These settings are correct for standard
operation of the device. Only the call-re-
lated fields KPAx - KPCx (with x varying
from 1 to 200) and any additional CLIP
numbers CLP1-CLP200 need to be set.
- BMOD (operation mode)=0 (single
key)
- TN1-TN5 (Administrator numbers)=
empty
- SL (security level)=0 (SMS from all)
- CLPEN (CLIP function)=1 (active)
- CLPOU (output activated by CLIP)=1
(output 1)
- LOT (maximum talk time)=90s
- OD1 (IN1 connected to output)=1 (clos-
ing of IN on GND activates output 1)
- OD2 (IN2 connected to output)=2
(closing of IN on GND activates out-
put 2)
- KPAx-KPCx (x from 1 to 200)= empty
(no call set)
- CLP1-CLP200=empty
- OS1 (contact activation 1)=3 s.
- OS2 (contact activation 2)=3 s.
KPABC
KPABC
KPABC
1 KPABC
KPABC 2
KPABC
KPABC 3 KPABC
KPABC 4 KPABC
KPABC 5 KPABC
KPABC 6 KPABC
KPABC 7 KPABC
KPABC 8 KPABC
9
KPABC KPABC
KPABC 10
KPABC
BMOD=0
Mi 2591
- 14 -
Making calls to user. How to
store phone numbers.
It is a device that uses the cellular radio
network to send the call and establish
an audio connection with the tenant, it is
necessary to store the telephone num-
bers of the users in AB4G. AB4G allows
a maximum of 200 different users to be
managed (this means it is possible to
send calls up to 200 housing units). In
addition, 3 telephone numbers can be
stored for each user. When the visitor is
in front of the push-button panel presses
one of the buttons, AB4G calls the first
of the stored telephone numbers for
that user. If the number is busy or does
not answer after a specific timeout time
(which can be set for each user of the
push button panel), a new call is made
to the second number and so on to the
third. The group of these 600 telephone
numbers is stored in the parameter set:
- KPA1, KPB1, KPC1 for the first user;
- KPA2, KPB2, KPC2 for the second user;
-..................
- KPA200, KPB200, KPC200 for the
200th user.
KPABC
11 23
KPABC
12 24
KPABC
13 25
KPABC
14 26
KPABC
15 27
KPABC
16 28
17 KPABC 29
18 KPABC 30
KPABC
19 31
KPABC
20 32
KPABC
21 33
KPABC
22 34
KPABC 25 KPABC 21
KPABC 26 KPABC 22
KPABC 3 KPABC 1 KPABC 27 KPABC 23
KPABC 4 KPABC 2 KPABC 28 KPABC 24
KPABC 9 KPABC 5 KPABC 33 KPABC 29
KPABC 10 KPABC 6 KPABC 34 KPABC 30
35 31
KPABC 11 KPABC 7 KPABC KPABC
36 32
KPABC 12 KPABC 8 KPABC KPABC
KPABC 41 KPABC 37
KPABC 17 KPABC 13
14 KPABC 42 KPABC 38
KPABC 18 KPABC
KPABC KPABC 15 KPABC 43 KPABC 39
19
KPABC 20 KPABC 16 KPABC 44 KPABC 40
BMOD=1
Storage can take place using one of
the three pogram methods shown in a
previous section. In the case of sending
an SMS, it is possible to proceed as in
the figure below:
New message
Send to
+443351234567
;KPA1=07172020
38;KPB1=335666
7666;KPC1=3330
002111;KPT1=30;
The pictures at the bottom of the page
show the correspondence between
call buttons and parameters KPA, KPB
and KPC in the case of single-button
(BMOD=0) or double-button (BMOD=1)
operation modes.
KPABC 49 KPABC
45
KPABC 50 KPABC 46
KPABC 51 KPABC 47
KPABC 52 KPABC 48
KPABC 57 KPABC 53
KPABC 58 KPABC 54
KPABC
KPABC 59 55
KPABC KPABC 56
60
KPABC KPABC
65 61
KPABC KPABC 62
66
KPABC 67 KPABC 63
KPABC 68 KPABC 64
BMOD=1