Publicidad
Idiomas disponibles
Idiomas disponibles
PRODUCT CHARACTERISTICS
Pneumatic shear is a tool powered by compressed air jet, it is used for for cutting sheets of steel and aluminium. Thanks to the
special system of blades, the edges of cut metal sheet do not bend during cutting. Tools are designed to operate indoors and they
should not be exposed to the infl uence of precipitation. The tool is not designed for continuous operation. Recommended mode of
operation is casual work during 5 minutes, then you should wait for 30 minutes, to cool the tool. Correct, reliable, and safe opera-
tion of the device is dependent on its proper use, therefore:
Prior to working with the tool, you should read all the instruction and keep it around.
For any damages or injuries caused by the tool misuse, resulting from failure to comply with its designation, non compliance with
with safety regulations and recommendations included in this manual, the supplier does not accept any liability. Using the product
without compliance to its intended to sign, results also in the loss of user's rights to the guarantee, as it would be a non-compli-
ance with the contract.
EQUIPMENT OF THE PRODUCT
The product has been equipped with a connector for connecting the product to the pneumatic system.
TECHNICAL DATA
Parameter
Catalog number
Weight
The diameter of the air connection (PT)
The diameter of the air inlet hose (internal)
Number of cuts
Cutting thickness
- in steel
- aluminium
Cutting width
Maximum operation pressure:
Required air fl ow (at 0.63 MPa)
Sound pressure (ISO 15744)
Sound pressure (ISO 15744)
Vibration (ISO 28927-9)
GENERAL SAFETY CONDITIONS
WARNING! When you are working with a pneumatic tool, we recommend that you always comply with the basic principles of occu-
pational safety, including the principles presented below, in order to reduce the risk of fi re, electric shock and to prevent injuries.
Prior to working with the tool, you should read all the instruction and keep it around.
ATTENTION! Read all the instructions below. Failure to comply with them can lead to electrical shock, fi re or personal injury. The
concept of "pneumatic tool", which is used in the instructions, refers to all tools, which are driven by a stream of air compressed
at the right pressure.
COMPLY WITH THE FOLLOWING INSTRUCTIONS
General safety conditions
Before starting the installation, work, repair, maintenance and changing of accessories, or when you are working near pneumatic
tool, because of many risks, you should read and understand the safety instructions. if the above mentioned steps are not taken,
it may result in serious injury. Installation adjustment and installation of pneumatic tools may be performed only by qualifi ed and
trained staff . Do not modify the pneumatic tool. Modifi cations can reduce the effi ciency and level of security, and increase the
risk for a tool operator. Do not discard the safety instructions, you must pass them to the tool operator. Do not use pneumatic
tool, when it is damaged. The tool should be subject to periodic inspections for visibility of the data required by ISO 11148. The
employer/user should contact the manufacturer for replacement of a rating plate whenever it is necessary.
Hazards associated with moving parts
Disconnect tool from the power supply before changing the inserted tool or accessory. Damage to the workpiece, accessories
O R I G I N A L
10
EN
Unit
[kg]
[" / mm]
[" / mm]
[min
-1
]
[mm]
[mm]
[mm]
[MPa]
[l/min]
[dB(A)]
[dB(A)]
[m/s
]
2
I N S T R U C T I O N S
Value
YT-09944
1.3
6.3 / 1/4
10 / 3/8
1800
1.2
1.4
5.5
0.63
141
80 ± 3
91 ± 3
6.5 ± 1.5
YT-09945
1.0
6.3 / 1/4
10 / 3/8
2500
1.2
1.4
5.5
0.63
141
90 ± 3
101 ± 3
4.6 ± 1.5
Publicidad
