Triton TSPS450 Instrucciones De Uso Y De Seguridad página 6

c) Prevent unintentional starting. Ensure the switch is in the
OFF-position before connecting to power source and/or
battery pack, picking up or carrying the tool. Carrying power
tools with your finger on the switch or energising power tools
that have the switch ON invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool ON. A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair and clothing away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and
properly used. Use of dust collection can reduce dust-related
hazards.
h) Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool safety
principles. A careless action can cause severe injury within a
fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it
ON and OFF. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or remove
the battery pack, if detachable, from the power tool before
making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power
tool's operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool bits, etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed. Use
of the power tool for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free
EN
from oil and grease. Slippery handles and grasping surfaces do
not allow for safe handling and control of the tool in unexpected
situations.
5) Service
a) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that
the safety of the power tool is maintained.
6
Ampere Rating Volts
120
240
More Not more
than than
0 6
6 10
10 12
12 16
WARNING: Before connecting a tool to a power source (mains
switch power point receptacle, outlet, etc.) be sure that the voltage
supply is the same as that specified on the nameplate of the tool. A
power source with a voltage greater than that specified for the tool
can result in serious injury to the user, and damage to the tool. If in
doubt, do not plug in the tool. Using a power source with a voltage
less than the nameplate rating is harmful to the motor.
Sanding Tool Safety
a) ALWAYS wear appropriate protective equipment, including
a dust mask with a minimum FFP2 rating, eye protection
and ear defenders
b) Ensure all people in the vicinity of the work area are also
equipped with suitable personal protective equipment
c) Take special care when sanding some woods (such as
beech, oak, mahogany and teak), as the dust produced is toxic
and can cause extreme reactions
d) NEVER use to process any materials containing asbestos.
Consult a qualified professional, if you are uncertain whether an
object contains asbestos
e) DO NOT sand magnesium or alloys containing a high
percentage of magnesium
f) Be aware of paint finishes or treatments that may have
been applied to the material that is being sanded. Many
treatments can create dust that is toxic, or otherwise
harmful. If working on a building constructed prior to 1960,
there is an increased chance of encountering lead-based paints
g) The dust produced when sanding lead-based paints is
particularly hazardous to children, pregnant women, and
people with high blood pressure. DO NOT allow these people
near to the work area, even if wearing appropriate personal
protective equipment
h) Whenever possible, use a vacuum dust extraction system
to control dust and waste
i) Be especially careful when using a machine for both wood
and metal sanding. Sparks from metal can easily ignite
wood dust. ALWAYS clean your machine thoroughly to reduce
the risk of fire
Table A
Total length of cord in metres (feet)
7.5 15 30.5
(25) (50) (100) (150)
15 30.5 61
(50) (100) (200) (300)
Minimum gauge for cord
18 16 16
18 16 14
16 16 14
14 12 Not
recommended
46
92
14
12
12