Publicidad
Idiomas disponibles
Idiomas disponibles
sity of the water out of spray nozzle is weaken.
Recommended cleaning procedure for the spray water sys-
tem:
(Fig 5 on page 5)
• Remove the block water board.
• Pull out the ice flopping shelf.
(Fig 6 on page 5)
• Take off the spray pipe connection (the silicone tube) then
take out the spray pipe.
(Fig 7 on page 5)
• Use proper tools to remove the spray nozzles and the nozzle
clamps as the direction one by one.
• Use water to clean the spray pipe and the nozzles with a soft
brush.
(Fig 8 on page 5)
• How to take out the spray pump.
Step 1: Unscrew the related screws on the back of the top plate,
then remove the top plate as the direction.
Step 2: The same way to remove the back plate.
(Fig 9 on page 6)
Step 3: Unplugging the power plug of the spray pump.
Step 4: Unscrew the three screws on the pump cover according
to the picture.
Step 5: Pull out the pump components.
(Fig 10 on page 6)
• Pull out the pump filter net as the direction.
• Use water to clean the filter net with a soft brush.
• Finally, install all of the parts back.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
• If the compressor stops for any reasons like water shortage,
ice full, power off, etc., don't restart it right away. You can
restart it 5 minutes later to protect compressor.
• Check regularly the connectors of the water inlet and outlet
tubes and drain the little surplus water that may occur.
• If the ice maker will be unused for long periods of time,
please pull out the drainage plug at the bottom of the water
box so as to drain the surplus water in the water box. Then in-
stall it back. Wipe the inner liner of the ice storage container
with a clean rag.
• Drainage: Pull out the drainage plug at the bottom of the wa-
ter box, after the water drained away, install it back.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
• Special care must be taken when moving or transporting the
machine due to its heavy weight. With at least 2 persons or
using a cart. Move the machine slowly, carefully, and never
incline more than 45°.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problem
Possible cause
Ice maker does
1. The voltage is out
not work.
of the limitation.
2. The ambient
temperature is
too low (lower
than 10°C).
Compressor
1. Refrigerant leaks.
works, but no
2. Refrigerating
ice was made.
system blocks.
3. Solenoid valve
failure.
4. Condensing fan
does not work.
5. Spray pump
blocks or failure.
Compressor
1. Water shortage.
does not work.
2. Ice full.
3. Compressor
stops (the tem-
perature of shell
is too high).
The indicator
1. Water shortage
of water short-
in water supply
system.
age lights.
2. Water inlet valve
damaged.
3. Tap water pres-
sure too low.
The indicator
1. There is some ice
of trouble
has not dropped.
lights.
2. Spray water
system blocks or
leakage.
GB
Possible solution
1. Turn off the
machine, restart it
when the voltage is
normal.
2. Try again when the
ambient tempera-
ture is over 10°C.
1. Refill the refrigerant
and test leakage.
2. Replace filter for the
N
filling system.
2
3. Replace the sole-
noid valve.
4. Replace the con-
densing fan.
5. Check the spray
pump and its filter
net.
1. Check the water
supply system
(water inlet valve
and water supply
tube).
2. Take some ice out.
3. Turn off the
machine and restart
1 hour later.
1. Check and make
sure the water
supply system is
fine, then restart.
2. Check the water
inlet valve.
3. If it is for tap water,
the water pressure
should not be lower
than 0.15 Mpa.
1. Check whether
the solenoid valve
could be open, if
not, replace with a
new one.
2. Check the spray
pump and its filter
net, check the spray
pipe and its nozzle,
check the spray pipe
connection.
13
Publicidad
