Publicidad
Idiomas disponibles
Idiomas disponibles
English
WARNING:
Ensure that the user is always connected to the anchorage point.
WARNING: Never use the tagline as a safety line. The tagline is NOT a part of fall arrest system. It is only an
accessory to the SRL, and it should NEVER be used as an extension to the lifeline.
WARNING: Also, make sure not to connect a connector to any element that may cause the hook or carabiner
material to distort, abrade or wear out.
WARNING:
The SRL should never be lubricated, and should always be kept away from oil.
If the DEWALT personal SRL'S with rebar hook confi guration is used, then the rebar hook should always be
connected to the anchorage structure, and NEVER to the dorsal D-ring of the full body harness. And the
DEWALT personal SRL's casing should always be worn at the harness end. A competent person must always
ensure compatibility of the anchorage structure with the DEWALT personal SRL'S
24) INSTALLATION AND USE OF DEWALT Personal SRL'S
DEWALT personal SRL'S can be used in both mobile and stationary applications.
•
For stationary application as anchor mounted SRL application, connect the anchorage eye of the SRL
housing with a connector conforming to ANSI Z359.12-2019, to an anchorage point at or above the dorsal
D-Ring and the snap hook of the DEWALT personal SRL'S to the dorsal D-ring of the full body harness of the
user. The distance of the anchor point ideally should not be more than 2 ft. (0.61 m) above the dorsal D-ring
of the harness.
•
For mobile application, connect the eye of the DEWALT personal SRL'S to the dorsal attachment D-ring of
the full body harness with the help of a connector/ carabiner conforming to ANSI Z359.12-2019, which is
compatible with the SRL subsystem, and ensure that the connector is locked. Now connect the hook at the
termination end of the DEWALT personal SRL'S to the anchorage structure.
Single Personal SRL's may be attached to the harness in one of three ways:
a )
With a carabiner meeting ANSI Z359.12-2019 directly to the harness dorsal D-Ring. (Fig. 1)
b )
With the supplied carabiner through the harness webbing below the dorsal D-Ring. (fig. 2-5)
c )
With the DEWALT twin personal SRL connector* to the harness personal SRL connector. (fig. 6-9)
Twin Personal SRL's should be attached to the harness with the DEWALT twin
personal SRL connector* to the harness personal SRL connector.
Connection to
D-Ring
Fig.1
Fig.1
Open carabiner
supplied with
unit and slide it
through the SRL
connection.
Fig.2
Fig.2
Slide the open
carabiner under
both pieces of
the webbing as
shown
Fig.3
Fig.3
12
(fig. 6-9)
Release the
carabiner to
ensure locking.
Fig.4
Fig.4
This is how it
will appear
when correctly
connected.
Fig.5
Fig.5
Twin Personal SRL's include the
personal SRL connector. Single
Personal SRL's include a carabiner.*
WARNING: ALWAYS avoid lifeline contact with sharp or abrasive edges and surfaces.
For using the DEWALT personal SRL's as a twin-leg option, assemble two DEWALT personal SRL'S to connect
under the webbing below the dorsal D-ring of the harness with the help of a special connector* (e.g.
DXFP990151). When using the DEWALT personal SRL'S as a twin-leg lifeline, then ensure 100% tie off at
all times. Make sure to disengage one hook from the anchorage structure only if the other hook is fi rmly
connected to the anchorage structure.
TWIN SRL Connector* Technical Specification
Model
Material of
Minimum
Construction
Breaking Strength
DXFP990151
Alloy Steel
5000 lbs. (23kN)
SRL CONNECTOR SOLD SEPARATELY*
Open connector
by pushing the
locking lever
and push button
at the end
simultaneously.
Fig.6
Fig.6
Slide Connector
through
Preinstalled
channel below
the Dorsal
D-ring.
Fig.7
Fig.7
Push the pin
inside the
grooves of the
connector to
ensure locking.
Fig.8
Fig.8
English
Now the block is
ready to use.
Fig.9
Fig.9
TIE BACK SRL's
STRUCTURAL ANCHOR(I-BEAM)
SNAP HOOK
ENERGY ABSORBING PACK
TO THIS EYE HOLE, ATTACH CARABINER
TO APPLICABLE HARNESS
INSTALLATION OF DEWALT SRL WITH TIE-BACK HOOK
DEWALT SRL with tie-back hook should be used with
the SRL casing attached to the Dorsal D-ring of the
full body harness, and the extended webbing (with
a sheath) wrapped around the anchorage structure,
and the tie-back hook secured around the webbing.
•
For tie-back applications, only use the models
identifi ed for tie-back applications.
•
Connection location must independently support
5,000 lbs. (23kN)
25) ADDITIONAL INFORMATION FOR SELF-
RETRACTING LIFELINES
Always tag as "Unsuitable" those SRL's which have
been found to be unsuitable for further use. Never
attempt to repair the equipment on your own. Send
the equipment so tagged to an authorized service
center (where the authorization has been received
from the manufacturer in writing), or back to the
manufacturer for replacement of components and
repair.
13
Publicidad
