Publicidad
be checked. That is very important if there is a chance the
discarded appliance to be used for play by children.
•
You should never keep the appliance unnecessarily
plugged-in. Disconnect the appliance from the mains if you
do not intend to use it for a long time.
•
In order to avoid any overheating of the electric cord it is
recommended to unreel the whole electric cord.
•
Warning: Do not use this appliance with a programmer,
counter or another device which can automatically turn
it on because if the appliance is covered or incorrectly
positioned there is a danger of fire.
•
Place the electric cord in such a way that it does not
hamper the movement of people and not to be stepped on!
You must use only approved connection blocks, which are
suitable for the appliance, i.e. there is a sign of compliance!
•
The electric cord must not be in touch with the hot parts
of the appliance!
•
You must never move the appliance by pulling it by
its electric cord. You must never use the electric cord for
moving of other objects.
•
Do not reel the electric cord round the appliance! Do not
use the appliance with its electric cord reeled – this is also
valid if a cable drum is used!
•
Do not press the cord and do not stretch it by sharp
edges. Do not place the cord over hot plates or in open fire!
II.
PACKAGE FIG. 1
•
After unpacking the appliance you should check if
it is not damaged during transportation and if all the
components are included! In case that you find out any
damage or incomplete package you should connect with
your authorized retailer!
•
Do not discard the original packing box! It could be
used to store the appliance during transportation in order
damages to be avoided!
•
The disposal of the packing material should be done in
the appropriate way! Children should be prevented from
playing with the polyethylene bags!
III.
MOUNTING ON A WALL FIG. 2
1.
Please ensure that the walls of the installation location
without wires, pipes, etc., to ensure that the device can be
securely mounted on the wall
2.
The appliance is intended only for vertical wall
mounting! Floor or ceiling mounting is forbidden!
3.
Never position the appliance right below a socket
outlet!
4.
The appliance should be assembled and connected by
a qualified electrician. The installation process should be
isolated from the mains before electrical connection works
are to be done.
5.
The power cord should not be in touch with hot parts
of the appliance!
6.
Do not use the appliance in rooms smaller than 4
square meters.
7.
The appliance inlet and outlet openings must not be
blocked! Distance between the appliance and the ceiling
is at least 0.2m. Distance on both sides of the appliance to
the wall is at least 0.25m. Distance between the outlet and
the bottom is min 1.2m.
English
IV.
MOUNTING FIG.3
1.
Choose a good horizontal position, then mark 2 points
as suggestive dimensions (170mm) on the drilling position,
then drill with a suitable drill holes at the marked locations
in the wall.
2.
Insert plastic anchors into the holes.
3.
Turn two stainless steel screws into the anchors and
leave 5 - 7 mm of the screw out.
4.
Put the appliance to the wall, pull down until it secured.
5.
Make sure that the round button mounted on the back
of the appliance is firmly mounted to the wall and has gone
in as far as possible. If this is not done, the appliance will not
turn on and function properly.
Warning: Before using the heater, make sure it
ismounted tightly to the wall.
We thank you for choosing TESY Bathroom Heater HL-
249VB W. This is a product, which provides heating at
2000W in cold weather in accordance with the desired
temperature conditions in the room. The appliance will
provide long-life service if being correctly maintained
and taken care of in accordance with the manual.
V.
OPERATION
Push the ON/OFF button (0/I) located at the back of the
appliance to connect power supply. There is a sound signal.
Then the appliance enters standby mode. Push the ON/OFF
button (0/I) again to stop the power supply.
Control panel fig. 4
Indicator
Name
Standby mode
Heating mode
Comfort mode
ECO mode
Display
How to use:
1.
Plug the appliance to type AC 230V 50-60Hz socket
and press the on/off switch (0/I) on the back cover
accompanied with sound signal. The indicator
up.
2.
Press
the button to turn on the heater.
3.
To stop the appliance from working, press the button
. The indicator
will display, then the appliance will
blow cool air around 60 seconds to discharge heat.
4.
Unplug the product when it's not in use.
Temperature setting :
When the screen display the target set temperature, press
and
to set the desired temperature:
•
Comfort mode or Comfort mode in programs P1/P2/
P3: Press
and
to set the temperature from 10-35 oC.
•
ECO mode or ECO mode in programs P1/P2/P3: Press
and
to set the temperature from 6-31 oC.
Button
Name
ON/OFF button
Increase button
Decrease button
Mode selection
Timer settings
lights
Usage and Storage Instructions
EN
5
Publicidad
