Publicidad
Idiomas disponibles
Idiomas disponibles
1 609 92A 7RT • 28.10.22 • PS
en
16
Secure the workpiece. A workpiece clamped
u
with clamping devices or in a vice is held more
secure than by hand.
In case of damage and improper use of the
u
battery, vapours may be emitted. The bat-
tery can set alight or explode. Ensure the
area is well ventilated and seek medical atten-
tion should you experience any adverse ef-
fects. The vapours may irritate the respiratory
system.
Do not open the battery. There is a risk of
u
short-circuiting.
The battery can be damaged by pointed ob-
u
jects such as nails or screwdrivers or by
force applied externally. An internal short
circuit may occur, causing the battery to burn,
smoke, explode or overheat.
Only use the AMPShare battery in the
u
manufacturer's products or those of the
AMPShare partners. This is the only way in
which you can protect the battery against dan-
gerous overload.
Protect the battery against heat,
e.g. against continuous intense sun-
light, fire, dirt, water and moisture.
There is a risk of explosion and short-
circuiting.
Do not touch any application tools or adja-
u
cent housing components shortly after op-
eration. These can become very hot during
operation and cause burns.
The application tool may jam during
u
drilling. Make sure you have a stable foot-
ing and hold the power tool firmly with
both hands. Otherwise you could lose control
of the power tool.
Take care when carrying out demolition
u
work using the chisel. Falling fragments of
the demolition material could injure you or
any bystanders.
Only charge the batteries using chargers
u
recommended by the manufacturer. A char-
ger that is suitable for one type of battery may
pose a fire risk when used with a different bat-
tery.
Hold the power tool firmly with both hands
u
and make sure you have a stable footing.
The power tool can be more securely guided
with both hands.
Product Description and
Specifications
Read all the safety and general in-
structions. Failure to observe the
safety and general instructions may
result in electric shock, fire and/or
serious injury.
English
Please observe the illustrations at the beginning
of this operating manual.
Do not use this power tool until you have
thoroughly read and fully understood this
operating manual. Pay additional attention to
the applicable national health and safety reg-
ulations.
Intended Use
English
The power tool is intended for hammer drilling in
concrete, brick and stone, as well as for light
chiselling work. It is also suitable for drilling
without impact in wood, metal, ceramic and
plastic. Power tools with electronic control and
right/left rotation are also suitable for screwdriv-
ing.
Product Features
English
The numbering of the product features refers to
the diagram of the power tool on the graphics
page.
(1)
SDS plus drill chuck
(2)
SDS plus tool holder
(3)
Dust protection cap
(4)
Locking sleeve
(5)
Vibration damping
(6)
EPC switch (Electronic Precision Control)
(7)
Mounting for suspension strap
(8)
Rechargeable battery release button
(9)
Rotational direction switch
(10)
Handle (insulated gripping surface)
(11)
On/Off switch
(12)
Rechargeable battery
(13)
Release button for impact/mode se-
lector switch
(14)
Impact/mode selector switch
(15)
Worklight
(16)
Button for depth stop adjustment
(17)
Auxiliary handle (insulated gripping sur-
face)
(18)
Depth stop
a) Accessories shown or described are not included
with the product as standard. You can find the
complete selection of accessories in our accessor-
ies range.
Technical Data
English
Cordless rotary
hammer
Article number
Speed control
Stop rotation
Clockwise/anticlock-
wise rotation
Rated voltage
a)
a)
ABH18-26AS
7 140 ...
●
●
●
V=
18
Publicidad
