Publicidad
Idiomas disponibles
Idiomas disponibles
Project Tips
•
Cut only with sharp blades; they cut cleaner, faster and put
less strain on the motor while cutting.
•
When cutting, always ensure that the pivoting shoe is
resting against the workpiece. This will improve operator
control and minimize vibration.
•
For longer blade life, use bi‑metal blades or carbide‑
tipped blades. These utilize a carbon steel back welded
to high speed steel teeth making the blade more flexible
and less prone to breaking.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the plastic materials used in
these parts. Use a cloth dampened only with water and
mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product,
e
use of such accessories with this product could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com.
Tool Connect™ Chip (Fig. L)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your
smart device (such as a smart phone or tablet) that connects
e
WALT. Call 1‑800‑4‑D
WALT
e
e
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
installing the Tool Connect™ Chip
1. Remove the retaining screws
Connect™ Chip protective cover
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
the screws.
4. Refer to Tool Connect™ Chip Instruction Sheet for
further instructions.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including
brush inspection and replacement, when applicable)
should be performed by a factory service center or
an authorized service center. Always use identical
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/account‑login.
WALT
Three‑Year Limited Warranty
For warranty terms, go to www.dewalt.com/support/
warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D
Joppa Road, Towson, MD 21286 or call 1‑800‑4‑D
(1‑800‑433‑9258).
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country‑specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1‑800‑4‑D
(1‑800‑433‑9258) for a free replacement.
12
that fasten the Tool
13
into the tool.
14
.
WALT Industrial Tool Co., 701 East
e
English
WALT
e
WALT
e
11
Publicidad
